Dell D28M Service Manual Download Page 39

Page: 39 / 94

CAUTION:

Removing the coin-cell battery resets the BIOS setup program’s settings to default. It is recommended

that you note the BIOS setup program’s settings before removing the coin-cell battery.

2. Remove the

left-side cover

3. Remove the

multiple graphics cards

About this task

The following images indicate the location of the coin-cell battery and provides a visual representation of the removal procedure.

Steps

1. Lay the computer on the right side.
2. Using a plastic scribe, push the coin-cell battery-release lever on the coin-cell battery socket to release the coin-cell battery out of the

socket.

3. Remove the coin-cell battery.

Installing the coin-cell battery

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the coin-cell battery and provides a visual representation of the installation procedure.

Disassembly and reassembly

Summary of Contents for D28M































































































Search results

Summary of Contents for D28M

Reviews:

Dell D28M, Service Manual, Page: 39 / 94

Search results

Summary of Contents for D28M

Reviews: