Dell D28M Service Manual Download Page 4

Page: 4 / 94

Installing the wireless card............................................................................................................................................32

Solid-state drive/Intel Optane........................................................................................................................................... 33

Graphics card.......................................................................................................................................................................36

Removing the graphics card........................................................................................................................................ 36
Installing the graphics card........................................................................................................................................... 37

Coin-cell battery.................................................................................................................................................................. 38

Removing the coin-cell battery....................................................................................................................................38
Installing the coin-cell battery...................................................................................................................................... 39

Power-supply unit............................................................................................................................................................... 40

Removing the power-supply unit.................................................................................................................................40
Installing the power-supply unit................................................................................................................................... 42

Processor fan and heat-sink assembly............................................................................................................................. 45

Processor..............................................................................................................................................................................48

Removing the processor...............................................................................................................................................48
Installing the processor................................................................................................................................................. 49

VR heat sink..........................................................................................................................................................................51

Removing the VR heat sink...........................................................................................................................................51
Installing the VR heat sink............................................................................................................................................. 51

Speaker.................................................................................................................................................................................52

Removing the speaker.................................................................................................................................................. 52
Installing the speaker.....................................................................................................................................................53

Power button....................................................................................................................................................................... 54

Removing the power button........................................................................................................................................ 54
Installing the power button.......................................................................................................................................... 55

Intrusion switch................................................................................................................................................................... 56

Removing the intrusion switch.................................................................................................................................... 56
Installing the intrusion switch....................................................................................................................................... 57

System board.......................................................................................................................................................................58

Removing the system board........................................................................................................................................ 58
Installing the system board...........................................................................................................................................62

3 System setup............................................................................................................................. 67

Contents

Summary of Contents for D28M































































































Search results

Summary of Contents for D28M

Reviews:

Related manuals for D28M

Brands by name

Popular brands

Dell D28M, Service Manual

Search results

Summary of Contents for D28M

Reviews:

Related manuals for D28M

Brands by name

Popular brands