Dell D28M Service Manual Download Page 58

Page: 58 / 94

Steps

1. Slide and place the intrusion switch in the chassis slot.
2. Connect the intruder cable to the system board.

Next steps

1. Install the

left-side cover

2. Follow the procedure in

After working inside your computer

System board

Removing the system board

Prerequisites

1. Follow the procedure in

Before working inside your computer

NOTE:

Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup

program after you replace the system board.

NOTE:

Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup

program. You must make the appropriate changes again after you replace the system board.

NOTE:

Before disconnecting the cables from the system board, note the location of the connectors so that you can

reconnect the cables correctly after you replace the system board.

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

solid-state drive/Intel Optane memory module

7. Remove the

graphics card

8. Remove the

coin-cell battery

9. Remove the

processor fan and heat-sink assembly

Disassembly and reassembly

Summary of Contents for D28M































































































Search results

Summary of Contents for D28M

Reviews:

Related manuals for D28M

Brands by name

Popular brands

Dell D28M, Service Manual

Search results

Summary of Contents for D28M

Reviews:

Related manuals for D28M

Brands by name

Popular brands