Dell D28M Service Manual Download Page 51

Page: 51 / 94

VR heat sink

Removing the VR heat sink

Prerequisites

1. Follow the procedure in

Before working inside your computer

WARNING:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool

before you touch it.

CAUTION:

For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in

your skin can reduce the heat transfer capability of the thermal grease.

2. Remove the

left-side cover

About this task

The following images indicate the location of the VR heat sink and provides a visual representation of the removal procedure.

Steps

1. Loosen the two captive screws that secure the VR heat sink to the system board.
2. Lift the VR heat sink off the system board.

Installing the VR heat sink

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the VR heat sink and provides a visual representation of the installation procedure.

Disassembly and reassembly

Summary of Contents for D28M































































































Search results

Summary of Contents for D28M

Reviews:

Related manuals for D28M

Brands by name

Popular brands

Dell D28M, Service Manual

Search results

Summary of Contents for D28M

Reviews:

Related manuals for D28M

Brands by name

Popular brands