Dell D28M Service Manual Download Page 69

Page: 69 / 94

Option

Description

Boot List Option

•

Legacy External Devices

•

UEFI—The

UEFI

option is enabled by default.

Advanced Boot Options

Allows you to select the Enable Legacy Option ROMs option, when in UEFI boot mode.

•

Enable Legacy Option ROMs—The

Enable Legacy Option ROMs

option is enabled by default.

•

Enable Attempt Legacy Boot

UEFI Boot Path Security

This option controls whether or not the system will prompt the user to enter the Admin password when
booting a UEFI boot path from the F12 Boot Menu.

•

Always, Except Internal HDD—The

Always, Except Internal HDD

option is enabled by default.

•

Always, Except Internal HDD&PXE

•

Always

•

Never

Date/Time

Allows you to set the date and time settings. Changes to the system date and time take effect
immediately.

System information

Table 4. System Configuration

Option

Description

Integrated NIC

Allows you to control the on-board LAN controller. The option

Enable UEFI Network Stack

is not

selected by default. The options are:

•

Disabled

•

Enabled

•

Enabled w/PXE: The

Enabled w/PXE

option is enabled by default.

NOTE:

Depending on the computer and its installed devices, the items that are listed

in this section may or may not be display.

Serial Port

This option determines how the integrated serial port operates.

The options are:

•

Disabled

•

COM1: The

COM1

option is enabled by default.

•

COM2

•

COM3

•

COM4

SATA Operation

This option enables you to configure the operating mode of the integrated SATA hard drive
controller.

The options are:

•

Disabled—The SATA controllers are hidden

•

AHCI—SATA is configured for AHCI mode

•

RAID ON—SATA is configured to support RAID mode. This option is enabled by default.

Drives

Allows you to enable or disable various drives on-board:

•

SATA-0

•

SATA-1

•

SATA-2

•

SATA-3

System setup

Summary of Contents for D28M































































































Search results

Summary of Contents for D28M

Reviews:

Related manuals for D28M

Brands by name

Popular brands

Dell D28M, Service Manual

Search results

Summary of Contents for D28M

Reviews:

Related manuals for D28M

Brands by name

Popular brands