Dell D28M Service Manual Download Page 76

Page: 76 / 94

Wireless options

Table 14. Wireless

Option

Description

Wireless Device Enable

Allows you to enable or disable the internal wireless devices.

The options are:

•

WLAN/WiGig

•

Bluetooth

All the options are enabled by default.

Maintenance

Table 15. Maintenance

Option

Description

Service Tag

Displays the service tag of your computer.

Asset Tag

If an asset tag is not set, this option enables you to create a system asset tag.

This option is disabled by default.

SERR Messages

Controls the SERR message mechanism. This option is set by default. Some graphics cards require that
the SERR message mechanism be disabled.

BIOS Downgrade

Allows you to flash previous revisions of the system firmware.

The option

Allow BIOS Downgrade

is enabled by default.

Data Wipe

This option enables you to securely erase data from all the internal storage devices. The process adheres
to SerialATA Security Erase and eMMC JEDEC Sanitize specifications. The option

Wipe on Next Boot

disabled by default.

Bios Recovery

BIOS Recovery from Hard Drive

—This option is set by default. Allows you to recover the corrupted

BIOS from a recovery file on the hard drive or an external USB drive.

BIOS Auto-Recovery

—Allows you to recover the BIOS automatically.

First Power On Date

Allows you the set Ownership date. The option

Set Ownership Date

is not set by default.

System logs

Table 16. System Logs

Option

Description

BIOS events

Allows you to view and clear the System Setup (BIOS) POST events.

Advanced configuration

Table 17. Advanced configuration

Option

Description

ASPM

Allows you to set the ASPM level.

•

Auto (default) - There is handshaking between the device and PCI Express hub to determine the
best ASPM mode supported by the device

System setup

Summary of Contents for D28M































































































Search results

Summary of Contents for D28M

Reviews:

Dell D28M, Service Manual, Page: 76 / 94

Search results

Summary of Contents for D28M

Reviews: