manualshive.com logo in svg

Dell D28M, Service Manual, Page: 75 / 94

Share
Download
Dell D28M Service Manual Download Page 75

Option

Description

•

Thorough — The system does not skip any steps in the boot process.

•

Auto — This allows the operating system to control this setting (this works only when the 
operating system supports Simple Boot Flag).

This option is set to 

Thorough

 by default.

Extend BIOS POST Time

This option creates an additional pre-boot delay.

•

0 seconds

 (default)

•

5 seconds

•

10 seconds

Full Screen Logo

This option will display full screen logo if your image match screen resolution. The option Enable Full 
Screen Logo is not set by default.

Warnings and Errors

This option causes the boot process to only pause when warning or errors are detected. Choose any 
one of the option:

•

Prompt on Warnings and Errors 

(default)

•

Continue on Warnings

•

Continue on Warnings and Errors

Manageability

Table 12. Manageability

Option

Description

Intel AMT Capability

This option enables you to enable or disable Intel AMT capability. The options are:

•

Disabled

•

Enabled—enabled by default

•

Restrict MEBx Access

USB provision

This option is disabled by default.

MEBx Hotkey

This option is enabled by default.

Virtualization support

Table 13. Virtualization Support

Option

Description

Virtualization

This option specifies whether a Virtual Machine Monitor (VMM) can use the additional hardware 
capabilities that are provided by the Intel Virtualization technology.

The option 

Enable Intel Virtualization Technology

 is enabled by default.

VT for Direct I/O

Enables or disables the Virtual Machine Monitor (VMM) from using the additional hardware 
capabilities that are provided by the Intel Virtualization technology for direct I/O.

The option 

Enable VT for Direct I/O

 is enabled by default.

Trusted Execution

This option specifies whether a Measured Virtual Machine Monitor (MVMM) can use the additional 
hardware capabilities that are provided by Intel Trusted Execution Technology.

The option 

Trusted Execution

 is disabled by default.

System setup

75

Summary of Contents for D28M































































































Reviews:

No comments