Dell D28M Service Manual Download Page 31 | Manualshive

Page: 31 / 94

background image

Wireless card

Removing the wireless card

Prerequisites

1. Follow the procedure in

Before working inside your computer

.

left-side cover

About this task

The following images indicate the location of the wireless card and provides a visual representation of the removal procedure.

Steps

1. Lay the computer on the right side.
2. Remove the single (M2x3) screw that secures the wireless card to the system board.
3. Slide and lift the wireless-card bracket off the wireless card.
4. Disconnect the antenna cables from the wireless card.
5. Slide and remove the wireless card at an angle from the wireless-card slot.

Disassembly and reassembly

31

«
...
29
30
31
32
33
...
»

Summary of Contents for D28M































































































Reviews:

No comments

Related manuals for D28M

Brand: Tandy Pages: 82

FLEX-BX100-ULT5

Brand: IEI Technology Pages: 121

Adjustable Height Workstation

Brand: Rockler Pages: 8

Brand: Alera Pages: 12

Personal System/2 50

Brand: IBM Pages: 62

Brand: IBM Pages: 50

Brand: IBM Pages: 84

Brand: HP Pages: 108

Bc1500 - BladeSystem - Blade PC

Brand: HP Pages: 149

Compaq 18 All-in-One

Brand: HP Pages: 13

Compaq d538 CMT

Brand: HP Pages: 80

Brand: HP Pages: 7

Compaq dc7800 MT

Brand: HP Pages: 102

Brand: HP Pages: 105

Brand: HP Pages: 22

Compaq dc7800 Series

Brand: HP Pages: 276

Compaq dc7700 Ultra Slim Desktop (USDT) Business

Brand: HP Pages: 10

compaq d538 Series

Brand: HP Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands