Dell D28M Service Manual Download Page 47 | Manualshive

Page: 47 / 94

background image

Removing the processor fan and 65 W heat-sink assembly

Prerequisites

1. Follow the procedure in

Before working inside your computer

.

WARNING:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool

before you touch it.

CAUTION:

For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in

your skin can reduce the heat transfer capability of the thermal grease.

left-side cover

About this task

The following images indicate the location of the processor fan and 65 W heat-sink assembly and provides a visual representation of the
removal procedure.

Steps

1. Disconnect the processor-fan cable from the system board.
2. Loosen the four captive screws that secure the processor fan and heat-sink assembly to the system board.
3. Lift the processor fan and heat-sink assembly off the system board.

Installing the processor fan and 65 W heat-sink assembly

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

Disassembly and reassembly

47

«
...
45
46
47
48
49
...
»

Summary of Contents for D28M































































































Reviews:

No comments

Related manuals for D28M

Brand: Kaypro Pages: 157

Brand: Igel Pages: 2

D-3362-I Series

Brand: Icop Pages: 14

Brand: Everex Pages: 47

Brand: XtendLan Pages: 17

Brand: WinSystems Pages: 53

Brand: Commodore Pages: 23

Brand: Cartft Pages: 10

Brand: Alienware Pages: 20

Brand: StarTech.com Pages: 29

Brand: Packard Bell Pages: 13

Brand: Packard Bell Pages: 15

Brand: HP Pages: 1

Brand: HP Pages: 1

Brand: HP Pages: 1

Pavilion t400 - Desktop PC

Brand: HP Pages: 2

Pavilion t400 - Desktop PC

Brand: HP Pages: 2

Brand: HP Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands