background image

4-14

Maintaining the printer

                    

User’s Guide for Magna™ Platinum Series™ Printers

particles on rollers. Set the prompted cleaning cycle more often than the default of 
every 250 cards. 

Clean printer rollers regularly, such as weekly, or every 1000 cards. If your printer 
is connected over a network using a print server, the cleaning frequency set in the 
printer will apply to cards sent from all attached PCs.

If you use StickiCards™, clean the card tracks after every 100 cards. Use the 
cleaning pen to reach most areas of the card track. Use an isopropyl alcohol swab 
(not included in the cleaning kit) to reach hidden areas of the card track.

If the printer includes an optional topcoat or overlay module, use the cleaning pen 
to remove deposits from the guides of the supply cartridge. Clean the guides on a 
regular basis, such as weekly.

Cleaning the printhead

The printhead can have contamination stuck to it. You might notice it as unprinted 
lines on printed cards. Clean the printhead only when needed, such as:

The printhead has been accidently touched, such as when changing supplies or 
clearing a card jam

You have replaced the printhead

Your observe problems with card appearance, as described in 

“Troubleshooting” 

on page 5-1.

Do not touch the printing edge of the printhead cartridge with your fingers. The oils 
on your fingers can reduce print quality.

Do not bump the printing edge of the printhead cartridge with any sharp objects. 
Sharp objects can permanently damage the printhead.

Use the cleaning pen to clean the printhead. Do not use a cotton swab. The fibers 
from the cotton can stick to the printhead. 

Clean the printhead

1

Power off the printer and disconnect it from the power source.

If your printer has a locking cover, unlock the cover before opening it.

2

Open the printer cover.

3

Press down on the swing arm. The push latch will release the swing arm. Using 
the handle, lift the swing arm until it is fully open.

4

Open the cleaning pen.

5

Using gentle pressure, move the cleaning pen back and forth along the full length 
of the printhead edge (see 

Figure 4-15

). Be sure to clean the rounded edge of the 

printhead completely.

!

!

i

Summary of Contents for ImageCard Magna





















































































































































































Reviews: