DataCard ImageCard Magna User Manual Download Page 104 | Manualshive

Page: 104 / 180

background image

6-6

Before you install

User’s Guide for Magna™ Platinum Series™ Printers

–

USB port (used with the Windows XP, Windows 2000, Windows Me, or
Windows 98 operating system)

•

The PC might have more than one USB port, or USB devices already
attached to the PC might provide USB ports to use.

Datacard recommends using the Windows 2000 or XP operating systems if
you plan to connect more than one printer to a PC using USB ports or using a
USB port and other connection methods.

–

A network connection to support printer sharing or direct networking

•

Have a CD-ROM drive to install the printer driver

•

Have one of the following operating systems:

–

Windows Me (recommended)

The Windows Me printer driver is also designed to work on Windows 98 or

Windows 98 Second Edition.

–

Windows XP with service pack 1 (recommended)

–

Windows 2000 with service pack 3

–

Windows NT 4.0 with service pack 5 or higher

The printer cannot be connected to a PC running Windows NT using a USB

port.

The PC must also have a card creation application that formats and prepares the card
data. For the PC requirements of your card creation application, see the application's
documentation.

ID system installation sequence

You might use this printer as part of an identification system (with a camera) or you
might use it with existing data and applications. When you set up this printer along
with other system components, install the printer driver after setting up the PC and
before installing the card creation application and capture software and devices. Verify
the success of each installation step before continuing.

i

E

E

«
...
102
103
104
105
106
...
»

Summary of Contents for ImageCard Magna





















































































































































































Reviews:

No comments

Related manuals for ImageCard Magna

Brand: Saxxot Pages: 13

Brand: Olivetti Pages: 438

da Vinci 1.0 Pro

Brand: XYZ Printing Pages: 11

Brand: BIXOLON Pages: 29

Brand: Oki Pages: 189

Brand: Zebra Pages: 29

Brand: Ricoh Pages: 156

Brand: Ricoh Pages: 2

Brand: Telpar Pages: 52

Brand: Lexmark Pages: 807

Brand: Jolimark Pages: 31

Brand: Airlink101 Pages: 36

Brand: SNBC Pages: 52

B-510DN - Business Color Ink Jet Printer

Brand: Epson Pages: 2

C117001-N - DFX 5000+ B/W Dot-matrix Printer

Brand: Epson Pages: 229

AcuLaser CX28 Series

Brand: Epson Pages: 328

B-310N - Business Color Ink Jet Printer

Brand: Epson Pages: 4

C094001 - FX 870 B/W Dot-matrix Printer

Brand: Epson Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands