Danfoss VLT FC 322 Design Manual Download

Page: 196 / 235

•

Auxiliary break contact on K1 prevents K3 to cut in.

•

RELAY 2 controls contactor K4 for on/off control of the fixed speed pump.

•

At alternation both relays de-energizes and now RELAY 2 will be energized as the first relay.

6.1.13 Start/Stop Conditions

Commands assigned to digital inputs. See

Digital Inputs, par.5-1*.

Variable speed pump (lead)

Fixed speed pumps

Start (SYSTEM START /STOP)

Ramps up (if stopped and there is a demand)

Staging (if stopped and there is a demand)

Lead Pump Start

Ramps up if SYSTEM START is active

Not affected

Coast (EMERGENCY STOP)

Coast to stop

Cut out (built in relays are de-energized)

Safety Interlock

Coast to stop

Cut out (built in relays are de-energized)

Function of buttons on Local Control Panel

Variable speed pump (lead)

Fixed speed pumps

Hand On

Ramps up (if stopped by a normal stop com-
mand) or stays in operation if already running

Destaging (if running)

Off

Ramps down

Cut out

Auto On

Starts and stops according to commands via ter-
minals or serial bus

Staging/Destaging

Automation VT Drive FC322 Design Guide

6 Application Examples

MG.20.X1.22 - VLT

is a registered Danfoss trademark

195

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20783-Danfoss-131X8145-VLT-Automation-VT-Drive-VFD-FC322-460V-.5-HP.aspx

Summary of Contents for VLT FC 322












































































































































































































































Search results

Summary of Contents for VLT FC 322

Reviews:

Related manuals for VLT FC 322

Brands by name

Popular brands

Danfoss VLT FC 322, Design Manual

Search results

Summary of Contents for VLT FC 322

Reviews:

Related manuals for VLT FC 322

Brands by name

Popular brands