Danfoss VLT FC 322 Design Manual Download

Page: 210 / 235

7.5 Examples

7.5.1 Writing a Parameter Value

Change par. 4-14

Motor Speed High Limit [Hz] to 100 Hz.

Write the data in EEPROM.

PKE = E19E Hex - Write single word in par. 4-14

Motor Speed High Limit

[Hz]
IND = 0000 Hex
PWEHIGH = 0000 Hex
PWELOW = 03E8 Hex - Data value 1000, corresponding to 100 Hz, see
Conversion.

The telegram will look like this:

Note: par. 4-14

Motor Speed High Limit [Hz] is a single word, and the

parameter command for write in EEPROM is “E”. Parameter number 4-14
is 19E in hexadecimal.

The response from the slave to the master will be:

7.5.2 Reading a Parameter Value

Read the value in par. 3-41

Ramp 1 Ramp Up Time

PKE = 1155 Hex - Read parameter value in par. 3-41

Ramp 1 Ramp Up

Time
IND = 0000 Hex
PWEHIGH = 0000 Hex
PWELOW = 0000 Hex

If the value in par. 3-41

Ramp 1 Ramp Up Time is 10 s, the response from

the slave to the master will be:

NB!

3E8 Hex corresponds to 1000 decimal. The conversion index for par. 3-41

Ramp 1 Ramp Up Time is -2, i.e. 0.01.

Par. 3-41 is of the type

Unsigned 32.

Automation VT Drive FC322 Design Guide

7 RS-485 Installation and Set-up

MG.20.X1.22 - VLT

is a registered Danfoss trademark

209

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20783-Danfoss-131X8145-VLT-Automation-VT-Drive-VFD-FC322-460V-.5-HP.aspx

Summary of Contents for VLT FC 322












































































































































































































































Search results

Summary of Contents for VLT FC 322

Reviews:

Related manuals for VLT FC 322

Brands by name

Popular brands

Danfoss VLT FC 322, Design Manual

Search results

Summary of Contents for VLT FC 322

Reviews:

Related manuals for VLT FC 322

Brands by name

Popular brands