Danfoss VLT FC 322 Design Manual Download Page 92 | Manualshive

Page: 92 / 235

Danfoss VLT FC 322 Design Manual Download Page 92

3.6.13 Brake Resistors

In applications where the motor is used as a brake, energy is generated in the motor and send back into the frequency converter. If the energy can not
be transported back to the motor it will increase the voltage in the converter DC-line. In applications with frequent braking and/or high inertia loads this
increase may lead to an over voltage trip in the converter and finally a shut down. Brake resistors are used to dissipate the excess energy resulting from
the regenerative braking. The resistor is selected in respect to its ohmic value, its power dissipation rate and its physical size. Danfoss offers a wide variety
of different resistors that are specially designed to our frequency converters. See the section

Control with brake function for the dimensioning of brake

resistors. Code numbers can be found in the section

How to order.

Automation VT Drive FC322 Design Guide

3 VLT Automation VT Drive Selection

MG.20.X1.22 - VLT

®

is a registered Danfoss trademark

91

3

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20783-Danfoss-131X8145-VLT-Automation-VT-Drive-VFD-FC322-460V-.5-HP.aspx

«
...
90
91
92
93
94
...
»

Summary of Contents for VLT FC 322












































































































































































































































Reviews:

No comments