manualshive.com logo in svg

Danfoss VLT FC 322, Design Manual, Page: 17 / 235

Share
Download
Danfoss VLT FC 322 Design Manual Download Page 17

 

2.1.2 Caution

The frequency converter DC link capacitors remain charged after power has been disconnected. To avoid an electrical shock hazard,
disconnect the frequency converter from the mains before carrying out maintenance. Wait at least as follows before doing service on
the frequency converter:

Voltage (V)

Min. Waiting Time (Minutes)

4

15

20

30

40

200 - 240

0.25 - 3.7 kW

5.5 - 45 kW

 

 

 

 

 

 

 

 

380 - 480

0.37 - 7.5 kW

11 - 90 kW

110 - 250 kW

315 - 1000 kW

 

 

 

 

 

 

525-600

0.75 kW - 7.5 kW

11 - 90 kW

 

 

315 - 1200 kW

 

 

 

 

 

525-690

 

11 - 90 kW

45 - 400 kW

450 - 1200 kW

 

 

 

 

 

 

Be aware that there may be high voltage on the DC link even when the LEDs are turned off.

 

2.1.3 Disposal Instruction 

Equipment containing electrical components may not be disposed of together with domestic
waste.
It must be separately collected with electrical and electronic waste according to local and cur-
rently valid legislation.

2.2 Software Version 

2.2.1 Software Version and Approvals

VLT Automation VT Drive FC322

Software version: 1.7x

 

 

 

This manual can be used with all VLT Automation VT Drive FC322 frequency converters with software version 1.7x.
The software version number can be found in parameter 15-43.

2 Introduction to VLT Automation VT Drive

Automation VT Drive FC322 Design Guide

16

MG.20.X1.22 - VLT

®

 is a registered Danfoss trademark

2  

Remote Site Products  -  1-888-532-2706  -  www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20783-Danfoss-131X8145-VLT-Automation-VT-Drive-VFD-FC322-460V-.5-HP.aspx

Summary of Contents for VLT FC 322












































































































































































































































Reviews:

No comments