manualshive.com logo in svg

Danfoss VLT FC 322, Design Manual, Page: 158 / 235

Share
Download
Danfoss VLT FC 322 Design Manual Download Page 158

NB!

The motor cable must be screened/armoured. If an unscreened/unarmoured cable is used, some EMC requirements are not complied
with. Use a screened/armoured motor cable to comply with EMC emission specifications. For more information, see 

EMC specifica-

tions in the Design Guide.

See section 

General Specifications for correct dimensioning of motor cable cross-section and length.

Screening of cables:

Avoid installation with twisted screen ends (pigtails). They spoil the screening effect at higher frequencies. If it is necessary to break the screen to install
a motor isolator or motor contactor, the screen must be continued at the lowest possible HF impedance.

Connect the motor cable screen to both the de-coupling plate of the frequency converter and to the metal housing of the motor.

Make the screen connections with the largest possible surface area (cable clamp). This is done by using the supplied installation devices within the
frequency converter.

Cable-length and cross-section:

The frequency converter has been EMC tested with a given length of cable. Keep the motor cable as short as possible to reduce the noise level and
leakage currents.

Switching frequency:

When frequency converters are used together with Sine-wave filters to reduce the acoustic noise from a motor, the switching frequency must be set
according to the instruction in par. 14-01 

Switching Frequency.

Term. no.

96

97

98

99

 

 

 

U

V

W

PE

1)

 

Motor voltage 0-100% of mains voltage.
3 wires out of motor

 

 

 

U1

V1

W1

PE

1)

 

Delta-connected

W2

U2

V2

 

6 wires out of motor

 

U1

V1

W1

PE

1)

 

Star-connected U2, V2, W2
U2, V2 and W2 to be interconnected separately.

1)

Protected Earth Connection

NB!

In motors without phase insulation paper or other in-
sulation reinforcement suitable for operation with volt-
age supply (such as a frequency converter), fit a Sine-
wave filter on the output of the frequency converter.

Automation VT Drive FC322 Design Guide

5 How to Install

MG.20.X1.22 - VLT

®

 is a registered Danfoss trademark

157

  5

Remote Site Products  -  1-888-532-2706  -  www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20783-Danfoss-131X8145-VLT-Automation-VT-Drive-VFD-FC322-460V-.5-HP.aspx

Summary of Contents for VLT FC 322












































































































































































































































Reviews:

No comments