Danfoss VLT FC 322 Design Manual Download Page 26 | Manualshive

Page: 26 / 235

Danfoss VLT FC 322 Design Manual Download Page 26

2.8.3 Local (Hand On) and Remote (Auto On) Control

The frequency converter can be operated manually via the local control panel (LCP) or remotely via analog/digital inputs or serial bus.
If allowed in par. 0-40

[Hand on] Key on LCP, par. 0-41 [Off] Key on LCP, par. 0-42 [Auto on] Key on LCP, and par. 0-43 [Reset] Key on LCP, it is possible

to start and stop the frequency converter byLCP using the [Hand ON] and [Off] keys. Alarms can be reset via the [RESET] key. After pressing the [Hand
On] key, the frequency converter goes into Hand Mode and follows (as default) the Local reference set by using the LCP arrow keys up [

▲

] and down

[

▼

].

After pressing the [Auto On] key, the frequency converter goes into Auto
mode and follows (as default) the Remote reference. In this mode, it is
possible to control the frequency converter via the digital inputs and var-
ious serial interfaces (RS-485, USB, or an optional fieldbus). See more
about starting, stopping, changing ramps and parameter set-ups etc. in
par. group 5-1* (digital inputs) or par. group 8-5* (serial communica-
tion).

130BP046.10

Hand Off
Auto
LCP Keys

Reference Site
par. 3-13

Reference Site

Active Reference

Hand

Linked to Hand / Auto

Local

Hand -> Off

Linked to Hand / Auto

Local

Auto

Linked to Hand / Auto

Remote

Auto -> Off

Linked to Hand / Auto

Remote

All keys

Local

Local

All keys

Remote

Remote

The table shows under which conditions either the Local Reference or the Remote Reference is active. One of them is always active, but both can not be
active at the same time.

NB!

Local Reference will be restored at power-down.

par. 1-00

Configuration Mode determines what kind of application control principle (i.e. Open Loop or Closed loop) is used when the Remote reference

is active (see table above for the conditions).

Automation VT Drive FC322 Design Guide

2 Introduction to VLT Automation VT Drive

MG.20.X1.22 - VLT

®

is a registered Danfoss trademark

25

2

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20783-Danfoss-131X8145-VLT-Automation-VT-Drive-VFD-FC322-460V-.5-HP.aspx

«
...
24
25
26
27
28
...
»

Summary of Contents for VLT FC 322












































































































































































































































Reviews:

No comments