Danfoss VLT FC 322 Design Manual Download Page 135

Page: 135 / 235

Illustration 5.8: Recommended lifting method, frame size
F4.

5.2.5 Tools Needed

To perform the mechanical installation the following tools are needed:

•

Drill with 10 or 12 mm drill

•

Tape measure

•

Wrench with relevant metric sockets (7-17 mm)

•

Extensions to wrench

•

Sheet metal punch for conduits or cable glands in IP 21/Nema 1 and IP 54 units

•

Lifting bar to lift the unit (rod or tube max. Ø 25 mm (1 inch), able to lift minimum 400 kg (880 lbs)).

•

Crane or other lifting aid to place the frequency converter in position

•

A Torx T50 tool is needed to install the E1 in IP21 and IP54 enclosure types.

5 How to Install

Automation VT Drive FC322 Design Guide

134

MG.20.X1.22 - VLT

is a registered Danfoss trademark

Remote Site Products - 1-888-532-2706 - www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20783-Danfoss-131X8145-VLT-Automation-VT-Drive-VFD-FC322-460V-.5-HP.aspx

Summary of Contents for VLT FC 322












































































































































































































































Search results

Summary of Contents for VLT FC 322

Reviews:

Danfoss VLT FC 322, Design Manual, Page: 135 / 235

Search results

Summary of Contents for VLT FC 322

Reviews: