manualshive.com logo in svg

Danfoss VLT FC 322, Design Manual, Page: 40 / 235

Share
Download
Danfoss VLT FC 322 Design Manual Download Page 40

2.9  Galvanic isolation (PELV) 

2.11.1 PELV - Protective Extra Low Voltage 

PELV offers protection by way of extra low voltage. Protection against electric shock is ensured when the electrical supply is of the PELV type and the
installation is made as described in local/national regulations on PELV supplies.

All control terminals and relay terminals 01-03/04-06 comply with PELV (Protective Extra Low Voltage) (Does not apply to grounded Delta leg above 400
V).

Galvanic (ensured) isolation is obtained by fulfilling requirements for higher isolation and by providing the relevant creapage/clearance distances. These
requirements are described in the EN 61800-5-1 standard.

The components that make up the electrical isolation, as described below, also comply with the requirements for higher isolation and the relevant test
as described in EN 61800-5-1.
The PELV galvanic isolation can be shown in six locations (see illustration):

In order to maintain PELV all connections made to the control terminals must be PELV, e.g. thermistor must be reinforced/double insulated.

1.

Power supply (SMPS) incl. signal isolation of U

DC

, indicating the

intermediate current voltage.

2.

Gate drive that runs the IGBTs (trigger transformers/opto-cou-
plers).

3.

Current transducers.

4.

Opto-coupler, brake module.

5.

Internal inrush, RFI, and temperature measurement circuits.

6.

Custom relays.

Illustration 2.5: Galvanic isolation

The functional galvanic isolation (a and b on drawing) is for the 24 V back-up option and for the RS 485 standard bus interface.

Installation at high altitude:
380 - 500 V, enclosure A, B and C: At altitudes above 2 km, please contact Danfoss regarding PELV.
380 - 500 V, enclosure D, E and F: At altitudes above 3 km, please contact Danfoss regarding PELV.
525 - 690 V: At altitudes above 2 km, please contact Danfoss regarding PELV.

Automation VT Drive FC322 Design Guide

2 Introduction to VLT Automation VT Drive

MG.20.X1.22 - VLT

®

 is a registered Danfoss trademark

39

  2

Remote Site Products  -  1-888-532-2706  -  www.remotesiteproducts.com

http://www.remotesiteproducts.com/p-20783-Danfoss-131X8145-VLT-Automation-VT-Drive-VFD-FC322-460V-.5-HP.aspx

Summary of Contents for VLT FC 322












































































































































































































































Reviews:

No comments