Danfoss VLT FC 103, Operating

Page: 142 / 182

FC 102 N110 N132 N160 N200 N250 N315
Drive module power loss at 460 V
[W]
(1)(2)(3)
2261 2724 3628 3569 4566 5714
Drive efficiency
(2)
0.98 0.98 0.98 0.98 0.98 0.98
Output frequency [Hz]
(4)
0–590 0–590 0–590 0–590 0–590 0–590
Heat sink overtemperature trip [°C
(°F)] 110 (230) 110 (230) 110 (230) 110 (230) 110 (230) 110 (230)
Control card overtemperature trip
[°C (°F)] 75 (167) 75 (167) 75 (167) 80 (176) 80 (176) 80 (176)
PHF overtemperature trip [°C (°F)] 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302)
dU/dt filter overtemperature trip
[°C (°F)] 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302)
Sine-wave filter overtemperature
trip [°C (°F)] 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302)
1
Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimension-
ing of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control card power
consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-efficiency-direc-
tive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each
add only 4 W.
2
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficiency
class, see the Ambient Conditions section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3
See also Input Power Option Losses section.
4
If using an output filter, the output frequency is limited further. See the Motor Output (U, V, W) section.
Table 97: Electrical Data, Mains Supply 3x380–480 V AC
FC 102 N355 N400 N450 N500 N560
Normal overload
110% torque for a duration of 60 s.
NO NO NO NO NO
Typical shaft output at 400 V [kW] 355 400 450 500 560
Typical shaft output at 460 V [hp] 500 600 600 650 750
Typical shaft output at 480 V [kW] 400 500 530 560 630
Enclosure size E5h E5h E5h E6h E6h
Output current (3-phase)
Continuous (at 400 V) [A] 658 745 800 880 990
Intermittent (60 s overload) (at 400 V) [A] 724 820 880 968 1089
Continuous (at 460/480 V) [A] 590 678 730 780 890
Intermittent (60 s overload) (at 460/480
V) [A] 649 746 803 858 979
Continuous kVA (at 400 V) [kVA] 456 516 554 610 686
Continuous kVA (at 460 V) [kVA] 470 540 582 621 709
AQ357954340588en-000201 / 130R0881 142 | Danfoss A/S © 2020.09
Specifications
VLT® Refrigeration Drive FC 103
Operating Guide