Danfoss VLT FC 103, Operating

Page: 145 / 182

FC 102 N110 N132 N160 N200 N250 N315 N400 N450
- Mains with contactor
[mm
2
(AWG)]
2x95
(2x3/0
mcm) 2x95
(2x3/0
mcm) 2x95
(2x3/0
mcm) 2x185
(2x350
mcm) 2x185
(2x350
mcm) 2x185
(2x350
mcm) 2x185
(2x350
mcm) 4x127
(4x250
mcm)
- Motor [mm
2
(AWG)] 2x95
(2x3/0
mcm) 2x95
(2x3/0
mcm) 2x95
(2x3/0
mcm) 2x185
(2x350
mcm) 2x185
(2x350
mcm) 2x185
(2x350
mcm) 2x185
(2x350
mcm) 4x127
(4x250
mcm)
Drive module power loss
at 600 V [W]
(1)(2)(3)
1740 2101 2649 3074 3723 4465 5028 6062
Drive module power loss
at 690 V [W]
(1)(2)(3)
1798 2167 2740 3175 3851 4614 5155 5939
Drive efficiency
(2)
0.98 0.98 0.98 0.98 0.98 0.98 0.98 0.98
Output frequency [Hz]
(4)
0–590 0–590 0–590 0–590 0–590 0–590 0–590 0–500
Heat sink overtempera-
ture trip [°C (°F)] 110 (230) 110 (230) 110 (230) 110 (230) 110 (230) 110 (230) 110 (230) 110 (230)
Control card overtem-
perature trip [°C (°F)] 75 (167) 75 (167) 75 (167) 75 (167) 80 (176) 80 (176) 80 (176) 80 (176)
PHF overtemperature
trip [°C (°F)] 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302)
dU/dt filter overtemper-
ature trip [°C (°F)] 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302)
Sine-wave filter over-
temperature trip [°C (°F)] 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302) 150 (302)
1 Typical power loss is at normal conditions and expected to be within ±15% (tolerance relates to variety in voltage and cable conditions.) These
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies to dimension-
ing of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control card power
consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-efficiency-direc-
tive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for slots A and B each
add only 4 W.
2
Measured using 5 m (16.4 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy efficiency
class, see the Ambient Conditions section. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
3
See also Input Power Option Losses section.
4
If using an output filter, the output frequency is limited further. See the Motor Output (U, V, W) section.
Table 99: Electrical Data, Mains Supply 3x525–690 V AC
FC 102 N500 N560 N630 N710 N800
Normal overload
110% torque for a duration of 60 s.
NO NO NO NO NO
Typical shaft output at 550 V [kW] 400 450 500 560 670
Typical shaft output at 575 V [hp] 500 600 650 750 950
Typical shaft output at 690 V [kW] 500 560 630 710 800
Enclosure size E5h E5h E6h E6h E6h
Output current (3-phase)
Continuous (at 550 V) [A] 523 596 630 763 889
AQ357954340588en-000201 / 130R0881 | 145 Danfoss A/S © 2020.09
Specifications
VLT® Refrigeration Drive FC 103
Operating Guide