manualshive.com logo in svg

Danfoss VLT FC 103, Operating

Share
Download
Danfoss VLT FC 103 Operating Download Page 137

•
•
•
•
•
•

•
•
•

•

•
•
•

•
•

9.3.92 ALARM 244, Heat Sink Temperature

Cause

The maximum temperature of the heat sink has been exceeded. The temperature fault cannot reset until the temperature drops
below the defined heat sink temperature. The trip and reset points are different based on the power size. This alarm is equivalent to

Alarm 29, Heat Sink Temp

.

Troubleshooting

Check for the following:

Ambient temperature too high.
Motor cables too long.
Incorrect airflow clearance above or below the AC drive.
Blocked airflow around the unit.
Damaged heat sink fan.
Dirty heat sink.

9.3.93 WARNING 251, New Typecode

Cause

The power card or other components have been replaced, and the typecode has changed.

9.3.94 ALARM 421, Temperature Fault

Cause

A fault caused by the on-board temperature sensor is detected on the fan power card.

Troubleshooting

Check wiring.
Check the on-board temperature sensor.
Replace fan power card.

9.3.95 ALARM 423, FPC Updating

Cause

The alarm is generated when the fan power card reports it has an invalid PUD. The control card attempts to update the PUD. A
subsequent alarm can result depending on the update. See 

Alarm 424, FPC Update Successful

 and 

Alarm 425 FPC Update Failure

.

9.3.96 ALARM 424, FPC Update Successful

Cause

This alarm is generated when the control card has successfully updated the fan power card PUD.

Troubleshooting

Press [Reset] to stop the alarm.

9.3.97 ALARM 425, FPC Update Failure

Cause

This alarm is generated after the control card failed to update the fan power card PUD.

Troubleshooting

Check the fan power card wiring.
Replace fan power card.
Contact supplier.

9.3.98 ALARM 426, FPC Config

Cause

The number of found fan power cards does not match the number of configured fan power cards. See 

parameter group 15-6* Option

Ident 

for the number of configured fan power cards.

Troubleshooting

Check fan power card wiring.
Replace fan power card.

AQ357954340588en-000201 / 130R0881 | 137

Danfoss A/S © 2020.09

Maintenance, Diagnostics, and

Troubleshooting

VLT® Refrigeration Drive FC 103

Operating Guide

Summary of Contents for VLT FC 103























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands