D-Link 3010F - DES Switch Page 135 Web User Manual Download | Manualshive

Page: 135 / 281

background image

D-Link DES-3010FA/GA User Guide

Page 134

Section 11. Defining the Forwarding Database

Packets addressed to destinations stored in either the Static or Dynamic databases are immediately forwarded to
the port. The Dynamic MAC Address Table can be sorted by interface, VLAN, or MAC Address, whereas MAC
addresses are dynamically learned as packets from sources that arrive at the device. Static addresses are config-
ured manually.

An address becomes associated with a port by learning the port from the frame’s source address, but if a frame
that is addressed to a destination MAC address is not associated with a port, that frame is flooded to all relevant
VLAN ports. To prevent the bridging table from overflowing, a dynamic MAC address, from which no traffic arrives
for a set period, is erased.

This section contains information for defining both static and dynamic forwarding database entries, and includes
the following topics:

•

Defining Static Forwarding Database Entries

•

Defining Dynamic Forwarding Database Entries

«
...
133
134
135
136
137
...
»

Summary of Contents for 3010F - DES Switch


























































































































































































































































































Reviews:

No comments

Related manuals for 3010F - DES Switch

MMAC-Plus 9G426-02

Brand: Cabletron Systems Pages: 12

MMAC-Plus 9F310-02

Brand: Cabletron Systems Pages: 4

Brand: Cabletron Systems Pages: 16

Brand: cable matters Pages: 4

Brand: CableCreation Pages: 7

TECMA Silence Marine

Brand: Thetford Marine Pages: 9

Brand: Technische Alternative Pages: 4

Brand: DirectConnect Pages: 10

Brand: Phonocar Pages: 2

Brand: Labgear Pages: 8

Brand: LINK-MI Pages: 12

MISCOM7028GX Series

Brand: Maiwe Pages: 22

Brand: Eaton Pages: 12

Brand: Allen-Bradley Pages: 4

Brand: I-Rocks Pages: 18

Brand: Maiwe Pages: 14

Brand: QSFPTEK Pages: 11

Brand: Novus Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands