manualshive.com logo in svg

D-Link 3010F - DES Switch, Web User Manual

The D-Link 3010F - DES Switch offers exceptional performance and efficiency for your networking needs. With its advanced features and high-speed connectivity, this switch is a must-have for businesses and individuals alike. Enhance your network management experience by downloading the free Web User Manual from manualshive.com to maximize the full potential of this product.

Share
Download
background image

Configuring VLANs

Defining VLAN Interface Settings

Page 111 

•

Exclude (Gray) 

— Excludes the interface from the VLAN. However, the interface can be added to the VLAN 

through GARP. 

•

Forbidden (Red) 

— Denies the interface VLAN membership, even if GARP indicates the port is to be added.

Defining VLAN Interface Settings

The 

VLAN Interface Settings Page

 contains fields for managing ports that are part of a VLAN. The port default 

VLAN ID (PVID) is configured on the 

VLAN Interface Settings Page

. All untagged packets arriving at the device 

are tagged with the port PVID. To define VLAN interfaces:

1.

Click 

Basic Setup > VLAN > Membership > Interface Settings

. The 

VLAN Interface Settings Page 

opens.

Figure 62: VLAN Interface Settings Page

The 

VLAN Interface Settings Page

 contains the following fields:

•

Interface 

— Displays the port number included in the VLAN.

•

Interface VLAN Mode 

— Displays the port mode. The possible values are:

–

General

 — Indicates the port belongs to VLANs, and each VLAN is user-defined as tagged or untagged 

(full IEEE802.1q mode).

–

Access 

— Indicates a port belongs to a single untagged VLAN. When a port is in Access mode, the 

packet types which are accepted on the port cannot be designated. Ingress filtering cannot be enabled or 
disabled on an access port.

–

Trunk 

— Indicates the port belongs to VLANs in which all ports are tagged, except for one port that can 

be untagged.

Summary of Contents for 3010F - DES Switch


























































































































































































































































































Reviews:

No comments

Related manuals for 3010F - DES Switch

Keithley 707 Quick Reference Manual preview
707
Brand: Keithley Pages: 66
Maipu SM3100-28TC-AC Installation Manual preview
SM3100-28TC-AC
Brand: Maipu Pages: 21
Maico MVS 6 Mounting And Operating Instructions preview
MVS 6
Brand: Maico Pages: 56
Jabra LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES How To Connect preview
LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES
Brand: Jabra Pages: 4
DANLERS TLSW HB Installation Notes preview
TLSW HB
Brand: DANLERS Pages: 2
Kramer Sierra Pro XL 1616V3 Specifications preview
Sierra Pro XL 1616V3
Brand: Kramer Pages: 2
Raritan SwitchMan USB-Combo SW2 Brochure preview
SwitchMan USB-Combo SW2
Brand: Raritan Pages: 2
Cabletron Systems 9F426-03 Appendix preview
9F426-03
Brand: Cabletron Systems Pages: 14
PABX 208AC Instruction Manual preview
208AC
Brand: PABX Pages: 46
SUCO 0140 Series Operating Instructions preview
0140 Series
Brand: SUCO Pages: 2
Saitek Hi-Speed USB 2.0 Hub User Manual preview
Hi-Speed USB 2.0 Hub
Brand: Saitek Pages: 14
SMART-AVI DVN-8P Installation Manual preview
DVN-8P
Brand: SMART-AVI Pages: 2
Hama 42556 Operating Instructions Manual preview
42556
Brand: Hama Pages: 36
TRENDnet TE100-S16plus User Manual preview
TE100-S16plus
Brand: TRENDnet Pages: 32
Intellinet 560641 Instructions Manual preview
560641
Brand: Intellinet Pages: 12
Intermatic T2006 Supplementary Manual preview
T2006
Brand: Intermatic Pages: 1
SMC Networks D-P5DW Installation And Maintenance Manual preview
D-P5DW
Brand: SMC Networks Pages: 1
Greengate VNLW-P-1001-MV-N-W Installation Instructions Manual preview
VNLW-P-1001-MV-N-W
Brand: Greengate Pages: 2

Brands by name

Popular brands

Load more brands