D-Link 3010F - DES Switch Web User Manual Download

Page: 232 / 281

Viewing Statistics

Viewing Interface Statistics

Page 231

Viewing GVRP Statistics

The

GVRP Statistics Page

contains device statistics for GVRP. To view GVRP statistics:

•

Click

Advanced Setup > Interface Statistics > GVRP

. The

GVRP Statistics Page

opens.

Figure 148:GVRP Statistics Page

The

GVRP Statistics Page

contains the following fields:

•

Interface

—Specifies the interface type for which the statistics are displayed.

–

Port

—Indicates port statistics are displayed.

–

LAG

—Indicates LAG statistics are displayed.

•

Refresh Rate

—Indicates the amount of time that passes before the GVRP statistics are refreshed. The pos-

sible field values are:

–

15 Sec

—Indicates that the GVRP statistics are refreshed every 15 seconds.

–

30 Sec

—Indicates that the GVRP statistics are refreshed every 30 seconds.

–

60 Sec

—Indicates that the GVRP statistics are refreshed every 60 seconds.

–

No Refresh

—Indicates that the GVRP statistics are not refreshed.

•

Join Empty

—Displays the device GVRP Join Empty statistics.

•

Empty

—Displays the device GVRP Empty statistics.

•

Leave Empty

—Displays the device GVRP Leave Empty statistics.

•

Join In

—Displays the device GVRP Join In statistics.

•

Leave In

—Displays the device GVRP Leave in statistics.

•

Leave All

—Displays the device GVRP Leave all statistics.

Summary of Contents for 3010F - DES Switch


























































































































































































































































































Search results

Summary of Contents for 3010F - DES Switch

Reviews:

Related manuals for 3010F - DES Switch

Brands by name

Popular brands

D-Link 3010F - DES Switch, Web User Manual

Search results

Summary of Contents for 3010F - DES Switch

Reviews:

Related manuals for 3010F - DES Switch

Brands by name

Popular brands