D-Link 3010F - DES Switch Page 241 Web User Manual Download | Manualshive

Page: 241 / 281

background image

D-Link DES-3010FA/GA User Guide

Page 240

•

Jabbers

— Displays the total number of received packets that were longer than 1518 octets. This number

excludes frame bits, but includes FCS octets that had either a bad Frame Check Sequence (FCS) with an
integral number of octets (FCS Error) or a bad FCS with a non-integral octet (Alignment Error) number. The field
range to detect jabbers is between 20 ms and 150 ms.

•

Collisions

— Displays the number of collisions received on the interface since the device was last refreshed.

•

Utilization

— Displays the percentage of the interface utilized.

2.

Select an entry in the

History Entry

field. The Statistics are displayed.

Configuring RMON Events

This section includes the following topics:

•

Defining RMON Events Control

•

Viewing the RMON Events Logs

Defining RMON Events Control

The

RMON Events Control Page

contains fields for defining RMON events. To view RMON events:

•

Click

Advanced Setup > RMON > Events > Events Control

. The

RMON Events Control Page

opens.

Figure 154:RMON Events Control Page

«
...
239
240
241
242
243
...
»

Summary of Contents for 3010F - DES Switch


























































































































































































































































































Reviews:

No comments

Related manuals for 3010F - DES Switch

DGS-1224TP - Web Smart Switch

Brand: D-Link Pages: 52

Brand: D-Link Pages: 8

DES-3225G Series

Brand: D-Link Pages: 3

DES-1228 - Web Smart Switch

Brand: D-Link Pages: 69

Brand: D-Link Pages: 109

Brand: Barco Pages: 2

Brand: Gefen Pages: 11

xStack DES-3500 Series

Brand: D-Link Pages: 260

DXS-3600 Series

Brand: D-Link Pages: 48

DXS-3400 SERIES

Brand: D-Link Pages: 3

Web Smart Switch DGS-1210-16

Brand: D-Link Pages: 71

Brand: D-Link Pages: 3

Brand: D-Link Pages: 56

xStack DES-3800 Series

Brand: D-Link Pages: 326

xStack DES-3526

Brand: D-Link Pages: 222

Brand: D-Link Pages: 2

DXS-1210 Series

Brand: D-Link Pages: 20

xStack DGS-3427

Brand: D-Link Pages: 246

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands