D-Link 3010F - DES Switch Web User Manual Download | Manualshive

Page: 85 / 281

background image

D-Link DES-3010FA/GA User Guide

Page 84

•

Guest VLANs

— Provides limited network access to authorized ports. If a port is denied network access via

port-based authorization, but the Guest VLAN is enabled, the port receives limited network access. For exam-
ple, a network administrator can use Guest VLANs to deny network access via port-based authentication, but
grant Internet access to unauthorized users.

•

Unauthenticated VLANS

— Are available to users, even if the ports attached to the VLAN are defined as

unauthorized.

Defining Network Authentication Properties

The

Network Authentication Properties Page

allows network managers to configure network authentication

parameters. In addition, Guest VLANs are enabled from the

Network Authentication Properties Page

. To define

the network authentication properties:

1.

Click

Advanced Setup > Network Security > Authentication > Properties

. The

Network Authentication

Properties Page

opens.

Figure 41: Network Authentication Properties Page

The

Network Authentication Properties Page

contains the following fields:

•

Port-based Authentication State

— Enables and disables port-based authentication on the device. The

possible field values are:

–

Enable

— Enables port-based authentication on the device.

–

Disable

— Disables port-based authentication on the device.

«
...
83
84
85
86
87
...
»

Summary of Contents for 3010F - DES Switch


























































































































































































































































































Reviews:

No comments

Related manuals for 3010F - DES Switch

Brand: BABBITT Pages: 14

Brand: BABBITT Pages: 10

Brand: UNICOM Pages: 1

S5560S-EI Series

Brand: H3C Pages: 37

OfficeConnect WX4400

Brand: 3Com Pages: 528

QuantaMesh T1048-LB9

Brand: QCT Pages: 42

Brand: Eaton Pages: 4

Brand: A-Neuvideo Pages: 16

Brand: Black Box Pages: 9

Brand: S&S Northern Pages: 8

Brand: Labgear Pages: 8

ControlCenter-IP-XS

Brand: G&D Pages: 56

Brand: Lancom Pages: 71

TMS 5XX SE AQ-EU Series

Brand: Triax Pages: 6

Brand: Conceptronic Pages: 28

Brand: Rocstor Pages: 2

Brand: Opencockpits Pages: 30

Brand: 3onedata Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands