D-Link 3010F - DES Switch Web User Manual Download | Manualshive

Page: 26 / 281

background image

Mounting Device

Installing the Device

Page 25

Installing the Device

The device can be installed on a flat surface or mounted in a rack. This section includes the following topics:

•

Desktop or Shelf Installation

•

Rack Installation

Desktop or Shelf Installation

When installing the switch on a desktop or shelf, the rubber feet included with the device should first be attached.
Attach these cushioning feet on the bottom at each corner of the device.

Ensure the surface is be able to support the weight of the device and the device cables.

To install the device on a surface, perform the following:

1.

Attach the rubber feet on the bottom of the device. The following figure illustrates the rubber feet installation
on the device.

Figure 10: Installing Rubber Feet

2.

Set device down on a flat surface, while leaving 2 inches on each side and 5 inches at the back.

3.

Ensure that the device has proper ventilation by allowing adequate space for ventilation between the device
and the objects around the device.

Rack Installation

The device can be mounted in an EIA standard-sized, 19-inch rack, which can be placed in a wiring closet with
other equipment. To install, the device the mounting brackets must first be attached on the devices’s sides.

«
...
24
25
26
27
28
...
»

Summary of Contents for 3010F - DES Switch


























































































































































































































































































Reviews:

No comments

Related manuals for 3010F - DES Switch

DGS-1024D - Switch

Brand: D-Link Pages: 16

DGS-1016D - Switch

Brand: D-Link Pages: 44

DES-6000 Series

Brand: D-Link Pages: 3

DES-5024 - Switch

Brand: D-Link Pages: 2

DES-3828 - xStack Switch - Stackable

Brand: D-Link Pages: 3

Brand: D-Link Pages: 192

Brand: D-Link Pages: 9

Brand: D-Link Pages: 110

Brand: D-Link Pages: 10

Brand: D-Link Pages: 17

Brand: D-Link Pages: 4

Brand: D-Link Pages: 9

Brand: D-Link Pages: 4

DGS-105 - Switch

Brand: D-Link Pages: 4

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

BNI IOL-314-S52-P012

Brand: Balluff Pages: 22

Brand: Daxten Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands