manualshive.com logo in svg

D-Link 3010F - DES Switch, Web User Manual, Page: 45 / 281

Share
Download
D-Link 3010F - DES Switch Web User Manual Download Page 45

D-Link DES-3010FA/GA User Guide

Page 44 

Note

When selecting an option from the Startup menu, time must be taken into account. If no selection is made 
within 35 seconds (default), the device times out. This default value can be changed through the CLI.

Only technical support personnel can use Diagnostics Mode. For this reason, Diagnostics Mode is not described 
in this guide.

Software Download and Reboot

This section describes the procedures for downloading software and rebooting the system, and includes the 
following topics:

•

Software Download from the Startup Menu

•

Erasing the Flash File

•

Password Recovery

•

Software Download through TFTP Server

•

Software Download through XModem

Software Download from the Startup Menu

The software download procedure is performed when a new version must be downloaded to replace corrupted 
files, or when the system software must be upgraded. To download software from the Startup menu:

1.

From the Startup menu, press 

[1]

. The following prompt appears:

Downloading code using XMODEM

2.

When using HyperTerminal, click 

Transfer 

on the HyperTerminal Menu Bar.

3.

In the 

Filename

 field, enter the file path for the file to be downloaded. 

4.

Ensure that the Xmodem protocol is selected in the 

Protocol

 field.

5.

Press 

Send

. The software is downloaded. 

Note

After software download, the device reboots automatically.

Erasing the Flash File

In some cases, the device configuration must be erased. If the configuration is erased, all parameters configured 
via CLI, EWS, or SNMP must be reconfigured.

To erase the device configuration:

1.

From the Startup menu, press 

[2]

 within two seconds to erase the flash file. The following message is 

displayed:

Warning! About to erase a Flash file. 

Are you sure (Y/N)? y

2.

Press 

Y

. The following message is displayed.

Write Flash file name (Up to 8 characters, Enter for none.):config

File config (if present) will be erased after system initialization 

======== Press Enter To Continue ========

3.

Enter 

config

 as the name of the flash file. The configuration is erased and the device reboots. 

Summary of Contents for 3010F - DES Switch


























































































































































































































































































Reviews:

No comments