manualshive.com logo in svg

D-Link 3010F - DES Switch, Web User Manual

The D-Link 3010F - DES Switch offers exceptional performance and efficiency for your networking needs. With its advanced features and high-speed connectivity, this switch is a must-have for businesses and individuals alike. Enhance your network management experience by downloading the free Web User Manual from manualshive.com to maximize the full potential of this product.

Share
Download
background image

Configuring Quality of Service

Defining Bandwidth Settings

Page 187 

Defining Bandwidth Settings

The 

Bandwidth Settings Page

 defines the bandwidth settings for a specified egress interface. Modifying queue 

scheduling affects the queue settings globally. To define the bandwidth settings:

1.

Click 

Basic Setup > Quality of Service > General Settings > Bandwidth Settings

. The

 Bandwidth Settings 

Page

 opens.

Figure 119: Bandwidth Settings Page

The 

Bandwidth Settings Page

 displays the following fields:

•

Status 

— Indicates if rate limiting is enabled on the interface. The possible field values are: 

–

Enable 

— Indicates that rate limiting is enabled on the interface. 

–

Disable 

— Indicates that rate limiting is disabled on the interface. 

•

Rate Limit 

— Configures the rate to which traffic is limited. The range is 70 – 285,000 kbps. 

•

Committed Information Rate (CIR) 

— Defines the CIR rate. The possible field range is 4096-

1,000,000,000.

2.

Define the fields. 

3.

Click 

. The bandwidth settings are defined, and the device is updated.

Summary of Contents for 3010F - DES Switch


























































































































































































































































































Reviews:

No comments

Related manuals for 3010F - DES Switch

BABBITT LS8000 Owner'S Manual preview
LS8000
Brand: BABBITT Pages: 14
BABBITT LS6000 Owner'S Manual preview
LS6000
Brand: BABBITT Pages: 10
Eaton COOPER POWER SERIES Installation And Operation Instructions Manual preview
COOPER POWER SERIES
Brand: Eaton Pages: 16
Kathrein EXE 159 Manual preview
EXE 159
Brand: Kathrein Pages: 41
Ask HDSW0024M1 User Manual preview
HDSW0024M1
Brand: Ask Pages: 4
Larson Electronics EXHL-TRN-LE1 Series Manual preview
EXHL-TRN-LE1 Series
Brand: Larson Electronics Pages: 2
Transition Networks SISTG1040-242-LRT Install Manuals preview
SISTG1040-242-LRT
Brand: Transition Networks Pages: 31
3Com 3C16987 User Manual preview
3C16987
Brand: 3Com Pages: 62
B&B Electronics Elinx EIR510-2MC-T User Manual preview
Elinx EIR510-2MC-T
Brand: B&B Electronics Pages: 107
Accton Technology EH3008D Quick Installation Manual preview
EH3008D
Brand: Accton Technology Pages: 7
IOGear GHDMIMS52 Quick Start Manual preview
GHDMIMS52
Brand: IOGear Pages: 1
Pilz PSEN 1.2p-25 Operating Instructions Manual preview
PSEN 1.2p-25
Brand: Pilz Pages: 8
Bühler technologies Nivotemp NT-EL Installation And Operation Instructions Manual preview
Nivotemp NT-EL
Brand: Bühler technologies Pages: 20
Maiwe MISCOM7220G-4GF-16GT User Manual preview
MISCOM7220G-4GF-16GT
Brand: Maiwe Pages: 6
CAMBRIONIX U16S User Manual preview
U16S
Brand: CAMBRIONIX Pages: 37
Allied Telesis AT 8000/8POE Installation Manual preview
AT 8000/8POE
Brand: Allied Telesis Pages: 56
Dahua D-PFS3110-8ET1GT1GF-96 Quick Start Manual preview
D-PFS3110-8ET1GT1GF-96
Brand: Dahua Pages: 17
Intellinet 560757 User Manual preview
560757
Brand: Intellinet Pages: 12

Brands by name

Popular brands

Load more brands