Crow Shepherd Installation Manual Download Page 66

Page: 66 / 73

thecrowgroup.com

Page | 65

Areas

This part enables control of SHEPHERD™

panel

Areas:

Selection of the area to monitor/control

ARM:

Arming of the selected Area

DISARM:

Disarming of the selected Area

STAY:

Stay Arming of the selected Area

PANIC:

Press 5 sec to generate immediate Panic

Alarm

Note

: Only active zones will be listed

Zones

This part provides info/control on Zones

Names of the active zones

RSSI Signal of the zone

Type of connected device

State of the device

Related area of the zone

Status (Active/Bypass) of the zone

Statistic (if device compatible) for

Temperature, Air Quality, Humidity…

Add Zones

: online learning of devices

Outputs

This part enable control on Outputs

NAME:

Name of the outputs (ex: outdoor siren)

TYPE:

Type of Output: Wired, Siren, Smart Plug…

STATE:

Info on output trouble

STATUS:

Activation / Deactivation of the output

Summary of Contents for Shepherd










































































Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands

Crow Shepherd, Installation Manual

Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands