Crow Shepherd Installation Manual Download Page 57

Page: 57 / 73

thecrowgroup.com

Page | 56

Miscellaneous

Chime Control

Parameter

Description

Default Configuration

Chime Alarm Beeps to

Keypad

If a zone is programmed as a Chime zone and it activates, the

zone can sound the buzzer at Selected keypads for local alarm

signaling. The duration of the Chime beep is programmed. The

Chime function can also be locally disabled at each keypad

individually if not required

Not selected

User Options

Parameter

Description

Default Configuration

Cancel Handover Zone

Function in Stay Mode

If this option is selected, any zone programmed with the

handover feature will act as a normal delayed zone during Stay

mode (i.e. the handover feature will be ignored).

The zone will still have the normal handover feature during the

full arm state.

Not selected

Summary of Contents for Shepherd










































































Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands

Crow Shepherd, Installation Manual

Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands