Crow Shepherd Installation Manual Download Page 10

Page: 10 / 73

thecrowgroup.com

Page | 9

Installing the SHEPHERD™

Note:

Be sure that the control panel is mounted near a socket outlet that is easily accessible. The socket outlet for the power

supply of the control panel should have its own fuse circuit

Use Philips screwdriver to unscrew the 2 holding screws located at the bottom of the panel

The screws are handling by a hidden spring. They cannot be totally removed

Remove the front cover of the panel by tilt it outside

Place the unit on the wall

Use the water level indicator to position it straight on the wall

Mark the holding holes on the wall and drill the wall

Mount the unit on the wall with screws

Ethernet – Connect the Ethernet cable to a router or an internet outlet

GSM – Insert micro-SIM card into the SIM card slot

AC – Plug into a power outlet

Connect the backup battery

Insert back the front cover by tilting it inside

Close the 2 holding screws

Summary of Contents for Shepherd










































































Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands

Crow Shepherd, Installation Manual

Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands