Crow Shepherd Installation Manual Download Page 32

Page: 32 / 73

thecrowgroup.com

Page | 31

Zone Key switch

Parameter

Description

Default Configuration

Key Switch can ARM

This option enables Arming of the assigned Area via the Keyswitch

Key Switch can DISARM

This option enables Disarming of the assigned Area via the Key-

switch

Key Switch is normally

open

The key-switch can be a NO (Normally Open) or a NC (Normally

Closed) key-switch.

Key Switch is

momentary

The operation of the key-switch can be momentary or latching. If

this option is on, the key-switch operation is assumed to be

momentary. This means that each time the key-switch is operated

then released the area will toggle its current state (I.e. if armed it

will become disarmed or vice versa). If this option is turned off it

is assumed that the key-switch is a latching type. This means that

when the key-switch is operated and the key removed the

contacts remain in the same state. When a latching key-switch is

used, turning on the switch will arm the area and turning it off will

disarm the area.

Alarm to Output

Parameter

Description

Default Configuration

Zone alarm to outputs

If an Area is Armed and a zone assigned to that Area activates,

the zone can trigger selected Outputs for local alarm signaling.

This location assigns Zones to Outputs for alarms that occur

when in the Full Armed State

No Outputs selected

Zone stay alarm to outputs

If an Area has Stay Mode Armed and a zone assigned to that

Area activates, the zone can trigger selected Outputs for local

alarm signaling. This location assigns Zones to Outputs for

alarms that occur when Stay Mode is Armed

No Outputs selected

Zone 24H alarm to outputs

If a zone is programmed as one of 24 Hour type zone and if it is

open then the selected output(s) is activated for local alarm

signaling. In case of standard 24-hour zone the output will be

active for the full reset time. In case of 24-hour auto-reset zone

the output is deactivated when the reset time expires or if zone

is closed. If a zone is a 24-hour fire zone then the output will

pulse at a rate equals to the pulse time for that output.

No Outputs selected

Summary of Contents for Shepherd










































































Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands

Crow Shepherd, Installation Manual

Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands