Crow Shepherd Installation Manual Download Page 44

Page: 44 / 73

thecrowgroup.com

Page | 43

Report Channels

Click on a report channel 1-8 to display its options.

Channel Type

Parameter

Description

Default Configuration

TCP_IP

Set channel type as TCP/IP

Need to set Ethernet enabled to use this type of channel

Note:

The channel #8 is dedicated to

the CrowCloud™

™

connection;

please do not change these

settings.

Wi-Fi

Set channel type as Wi-Fi.

Need to set Wi-Fi enabled to use this type of channel

GPRS

Set channel type as 3G

Need to set 3G IP enabled to use this type of channel in setting

"Communication"

→

"GSM"

(see below in para "Communication")

SMS

Set channel type as SMS Text Messages

VOICE

Set channel type as a VOICE for voice Messages announcement to

telephone when the system is in ARM mode or to a local voice devise

when the system is in the DISARM

Summary of Contents for Shepherd










































































Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands

Crow Shepherd, Installation Manual

Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands