Crow Shepherd Installation Manual Download Page 4

Page: 4 / 73

thecrowgroup.com

Page | 3

The SHEPHERD™ Architecture

Features and Capabilities

Up To 20 Users

User Codes, and/or pendants, and/or Tags

Up to 64 2 Way Wireless Zones

Up to 64 Zones in Total, ISM (RF) , Extender ISM (RF)or/and DECT zones

Working modes options (normal, 24H, Chime, Zone is a key switch…)

Remotely zone configuration

Zone supervision

Zone is assigned to Cameras

…and more

Up to 32 Two Way Wireless Outputs

Up to 32 in Total, ISM (RF) ,ISM Extender or/and DECT outputs

Up to 4 Partitions (areas)

With Area Name customization

Alarm Detection devices

PIR, CRT, EDS3000AM, Magnet Contact, Glass break detector, Smoke

detector, MAG&Shock, AQ, and many more…see CROW web site for more

devices types

Visual verification

Up to 16 indoor or outdoor PIRCAM or mix of both detectors in total

Audio verification

SH-AVM is an indoor audio verification module, originating emergency

end to end user phone calls

Home Comfort devices

ACP Smart Plug , DB Doorbell devices, SH-AVM

Safety Devices

Smoke ,Flood, Air Quality , Temperature and Humidity detectors

Signaling Devices

Indoor and Outdoor sirens

Communication

GSM/GPRS/3G/LTE

Ethernet

WI-FI

SMS messages and SMS Control Commands

GSM calls for SH-AVM module full duplex calls

USB-C connector

For Factory use Only

Up To 8 report channels

TCP/IP channel

Wi-Fi channel

GSM/GPRS /3G/LTE channel

Backup function between communication report channels

SMS

Full Duplex voice calls on panic event or originating calls (with DECT Voice

devices)

Summary of Contents for Shepherd










































































Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands

Crow Shepherd, Installation Manual

Search results

Summary of Contents for Shepherd

Reviews:

Related manuals for Shepherd

Brands by name

Popular brands