Cosmo LS-1866 Operation Manual Download Page 54

Page: 54 / 94

8 COMPENSATION MODE (MASTER-PRESET)

8.1.2 Sampling by manual operation

<Operation>

Press the START key.

The sampling process proceeds in the following sequence:

DL1

→

CHG

→

DL2

→

BAL(1)

→

DET(1)

→

STB

→

BAL(2)

→

DET(2)

→

DL3

→

END

DET(1) is the DET stage in a normal leak test. Measured value during this stage includes true leakage and

drift. During STB the tested part and the master are re-pressurized and pneumatically equalized to let the

internal pressure stabilized until drift ceases.

<Stages>

1) CHG stage

After START key is pressed, the leak limit indicators

remains blank until at the end of CHG stage.

2) BAL (1) and DET (1) stages

The current differential pressure value is displayed on

the HI leak limit indicator during BAL (1) and DET (1)

stages.

3) STB stage

Stb

appears on the leak rate indicator, and the

measured differential pressure value during DET (1) on

the HI leak limit indicator is held.

4) BAL (2) and DET (2) stages

PrE

appears again on the leak rate indicator, the

differential pressure value during DET (1) shifts to the

LO leak limit indicator, and the differential pressure

value during DET (2) is displayed on HI leak limit

indicator during the BAL and DET stages.

5) When the DET (2) stage times out, the limit setting

indicator HI displays the Master-Preset value. Press

the

◄

LEFT key for longer than 1 second to display the

differential pressure of DET(1) on the leak rate

indicator, or press the RIGHT

►

key for longer than 1

second to display the differential pressure of DET(2) on

the leak rate indicator.

6) Press the STOP key to return to the Measurement

mode.

Press the ENTER key to manually edit a Master-Preset

value or sample Master-Preset value again. The leak

tester will return to the initial state of compensation

mode, with the entry digit positing of the Master-Preset

value blinking.

The setting of BAL(2) is same as that of BAL(1). The setting of DET(2) is

same as that of DET(1). BAL(2) and DET(2) cannot be set.

NOTE

Master-Preset value can also be manually entered with

▲

UP and DOWN

▼

keys.

Pressing the SHIFT key to move the setting digit to the left. Hold the

▲

UP or

DOWN

▼

key depressed to increase or decrease the number continuously.

NOTE

The tester transmits the [Clamp] and [Busy] signals in the Charge Delay (DL1)

stage. To use these signals in order to drive clamp fittings, adjust the timer for

this stage so that the tester moves to the Charge stage after clamping is

completed.

NOTE

Summary of Contents for LS-1866































































































Search results

Summary of Contents for LS-1866

Reviews:

Related manuals for LS-1866

Brands by name

Popular brands

Cosmo LS-1866, Operation Manual

Search results

Summary of Contents for LS-1866

Reviews:

Related manuals for LS-1866

Brands by name

Popular brands