manualshive.com logo in svg

COBHAM 2201R, Reference Manual

Share
Download
COBHAM 2201R Reference Manual Download Page 236

2201R Mobile Tester  SCPI Reference Guide

Chapter 10 Measurement commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

236

:MEASure:GPRS:ARRay:RFTX:POWer 

Syntax

:MEASure:GPRS:ARRay:RFTX:POWer <int1>

Parameters

int1 is an integer.
The minimum value for int1 is 0, the maximum value is 100. The default value for int1 is 0.

Description

Measures multiple times (set with the int1 parameter) the burst peak power. To read out the entire measurement 
results array, use the :FETCh:GPRS:RFTX:POWer command.

Query

The query form of this command returns a string, containing int1 floating point real numbers with the physical 
dimension of dBm, representing the measurement results. 
The single measurement results are separated by commas.

Example

:MEAS:GPRS:ARR:RFTX:POW? 5 
An example of the string returned is: "11.22,11.09,11.21,11.14,10.99".

:MEASure:GPRS:ARRay:RFTX:TEMPlate 

Syntax

:MEASure:GPRS:ARRay:RFTX:TEMPlate <int1>

Parameters

int1 is an integer.
The minimum value for int1 is 0, the maximum value is 100. The default value for int1 is 0.

Description

Checks multiple times (set with the int1 parameter) if TX burst fits into the power/time template. To read out the 
entire measurement results array, use the :FETCh:GPRS:RFTX:TEMPlate command. 
Note: The power/time template is user-definable. It can be set up using the :CALC:GPRS:RFTX:TEMP commands.

Query

The query form of this command returns a string, containing int1 boolean numbers. A 0 indicates no violation of the 
PTT by the current burst, while a 1 signals PTT violation. 
The single measurement results are separated by commas.

Example

:MEAS:GPRS:ARR:RFTX:TEMP 10 
:FETC:GPRS:RFTX:TEMP?
The check of the current burst against the PTT is performed ten times. The check results are stored internally and read 
out by the FETC command. An example of the string returned is: "0,0,0,0,0,0,1,0,0,0", indicating that the seventh burst 
checked violated the PTT.

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands