manualshive.com logo in svg

COBHAM 2201R, Reference Manual

Share
Download
COBHAM 2201R Reference Manual Download Page 133

2201R Mobile Tester  SCPI Reference Guide

Chapter 8 Configuration commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

133

:CONFigure:GPRS:MSTAtion:PLEVel[:ALL] 

Syntax

:CONFigure:GPRS:MSTAtion:PLEVel[:ALL] <int1>

Parameters

int1 is an integer.
The minimum value for int1 is 0, the maximum value is 31. The default value for int1 is 10.

Description

This command sets the mobile power control level.
Notes: 
The RF power control level is a code. The corresponding RF output power of the mobile under test depends on the 
type of GSM system and the frequency range.
The power control level is broadcast in the SACCH physical header.

Query

The query form of this command returns the current setting. The string delivered back contains one integer.

Example

:CONFigure:GPRS:MSTAtion:PLEVel:ALL 17
:CONF:GPRS:MSTA:PLEV?
Value returned: "17".

:CONFigure:GPRS:MSTAtion:MODE 

Syntax

:CONFigure:GPRS:MSTAtion:MODE <PredefExp>

Parameters

PredefExp is one of the following predefined expressions: FACCh|SDCCh.
Default is FACCh.

Description

Defines whether the call setup takes place on FACCh or on SDCCh.
Note: There are two standard signaling channels in GSM: SDCCH and FACCH. The FACCH is always associated with a 
traffic channel. However, some mobiles only listen to signaling provided on the SDCCH.

Query

The query form of this command returns the current setting. The string delivered back contains the short-form 
version of one of the predefined expressions explained above.

Example

:CONFigure:GPRS:BS:CMODe FACCh
:CONF:GPRS:BS:CMOD?
Value returned: "FACC".

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands