manualshive.com logo in svg

COBHAM 2201R, Reference Manual

Share
Download
COBHAM 2201R Reference Manual Download Page 185

2201R Mobile Tester  SCPI Reference Guide

Chapter 9 Call commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

185

EDGE commands

:CALL:EGPRs:MSINfo:ALL

Syntax

:CALL:EGPRs:MSINfo:ALL

Parameters

There are no parameters.

Description

This command reads out all EGPRS MS Info result values with one query.
The query delivers back 3 single values in the following sequence, all separated by commas:
- IMSI (String) This is the international mobile subscriber identity.
- IMEI (String) This position contains the international mobile equipment identity.
- MClass shows the GPRS multislot class reported by the MS. Valid return values are in the range 1 to 29.

Query

There is only a query form of this command available. The query returns a string containing 15 values coded as 
explained above.

Example

:CALL:EGPRs:MSINfo:ALL?
The string delivered back in this example is: "001010123456789",
"520040190000430",3.

:CALL:EGPRs:MSINfo:IMSI

Syntax

:CALL:EGPRs:MSINfo:IMSI

Parameters

There are no parameters.

Description

This query delivers back the international mobile subscriber identity as stored on the SIM card.

Query

There is only a query form of this command available. The query delivers back a string.

Example

:CALL:EGPRs:MSINfo:IMSI?
The string delivered back in this example is: "001010123456789".

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands