manualshive.com logo in svg

COBHAM 2201R, Reference Manual

Share
Download
COBHAM 2201R Reference Manual Download Page 101

2201R Mobile Tester  SCPI Reference Guide

Chapter 8 Configuration commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

101

:CONFigure:GSM:BER:COUNt 

Syntax

:CONFigure:GSM:BER:COUNt <long1>

Parameters

long1 is a long integer number.
The minimum value for long1 is 2,000, the maximum value is 1,000,000. The default value for long1 is 10,000.

Description

This command sets the number of bits that are used for a BER measurement.

Query

The query form of this command returns the current setting. The string delivered back contains one long integer 
number.

Example

:CONFigure:GSM:BER:COUNt 100000
:CONF:GSM:BER:COUN?
Value returned: "100000".

:CONFigure:GSM:BER:RTDelay 

Syntax

:CONFigure:GSM:BER:RTDelay <int1>

Parameters

int1 is an integer.
The minimum value for int1 is 0, the maximum value is 30. The default value for int1 is 0.

Description

This command allows to predefine a round trip delay in order to achieve a fast synchronization.
Note: During BER testing, there is a delay between the reception of the first burst of a particular voice block at the 
mobile and the transmission of the first burst of the same voice block (after decoding and coding) on the uplink. This 
delay is called the round trip delay.

Query

The query form of this command returns the current setting. The string delivered back contains one integer.

Example

:CONFigure:GSM:BER:RTDelay 9
:CONF:GSM:BER:RTD?
Value returned: "9"

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands