manualshive.com logo in svg

COBHAM 2201R, Reference Manual

Share
Download
COBHAM 2201R Reference Manual Download Page 139

2201R Mobile Tester  SCPI Reference Guide

Chapter 8 Configuration commands

47090/323

Copyright © 2016 Aeroflex Limited. All rights reserved.

139

:CONFigure:EGPRs:BS:ALPHa 

Syntax

:CONFigure:EGPRs:BS:ALPHa <int1>

Parameters

int1 is an integer.
The minimum value for int1 is 0, the maximum value is 15. The default value for int1 is 0.

Description

This command sets the alpha factor in (asynchronous) generator/analyzer mode (please refer to the description of 
the :CONF:CSYS:GPG command for further information).
The alpha factor is one of the GPRS power control parameters. It is required by the mobile to calculate the uplink 
power level it has to use on a PDCH (packed data channel).
The alpha factor is broadcast by the 2201R in the SI13 rest octets.

Query

The query form of this command returns the current setting. The string delivered back contains one integer.

Example

:CONFigure:EGPRs:BS:ALPHa 10
:CONF:EGPRs:BS:ALPH?
Value returned in this example: "10"

:CONFigure:EGPRs:BS:RLCMac:USF 

Syntax

:CONFigure:EGPRs:BS:RLCMac:USF <int1>

Parameters

int1 is an integer.
The minimum value for int1 is 0, the maximum value is 7. The default value for int1 is 0.

Description

This command sets the uplink state flag (USF) in (asynchronous) generator/analyzer mode (please refer to the 
description of the :CONF:CSYS:GPG command for further information).
The USF is used to either assign a block to a particular mobile (one out of seven possible) or to mark it as unassigned. 
All time slots use the same USF. The USF is part of the MAC header on the PDTCH

Query

The query form of this command returns the current setting. The string delivered back contains one integer.

Example

:CONFigure:EGPRs:BS:RLCMac:USF 0
:CONF:EGPRs:BS:RLCM:USF?
Value returned in this example: "0"

Summary of Contents for 2201R








































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands