manualshive.com logo in svg

Climax H&S TOOL SPEED FACER ODF100, Operating Manual

The Climax H&S TOOL SPEED FACER ODF100 is a high-performance portable machining tool designed for efficient and precise facing of pipe or vessel flanges. Ensure optimal performance by referring to the comprehensive Operating Manual available for free download from our website.

Share
Download
background image

P/N 102615, Rev. 0

Page v

 LIST OF FIGURES

F

IGURE

P

AGE

2-1 Extension feet installed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  10
2-2 Typical Speed Facer components (model ODF40 shown)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  11
2-3 PCU components  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  12
2-4 ODF30 Speed Facer dimensions (P/N 88930)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  14
2-5 ODF40 Speed Facer dimensions (P/N 86870)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  15
2-6 ODF50 Speed Facer dimensions (P/N 86980)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  16
2-7 ODF60 Speed Facer Dimensions (P/N 86990) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  17
2-8 ODF70 Speed Facer Dimensions (P/N 87000)   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  18
2-9 ODF80 Speed Facer dimensions (P/N 94770)    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  19
2-10 ODF90 Speed Facer dimensions (P/N 94780)    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  20
2-11 ODF100 Speed Facer dimensions (P/N 94790)    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
2-12 ODF110 Speed Facer Dimensions (P/N 93050) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2-13 ODF120 Speed Facer Dimensions (P/N 7639-S1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  23
3-1 Lifting points (ODF40 machine shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
3-2 Vertical hazard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  30
3-3 Mounting arrangements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31
3-4 Alternate mounting holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  31
3-5 Bolt and hole locations  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  32
3-6 Leveling foot components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  33
3-7 Chuck foot spacers  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  34
3-8 Dial indicator mounted for leveling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35
3-9 Location of swivel clamping screw  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  35
3-10 .50” tool adapter installed (P/N 89175)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36
3-11 Offset tool holder (P/N 89203) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  36
3-12 Feed tripper location  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37
3-13 Feed adjustments  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  37
3-14 Installed air motor drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38
3-15 Installed hydraulic motor drive (bottom side) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  38
4-1 Standard configuration (ODF80 shown)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  40
4-2 Gib lock screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  40
4-3 Backfacing configuration (ODF80 shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  41
4-4 Relocated motor and brace location (ODF80 shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4-5 Repositioned backfacing components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  42
4-6 Air caddy controls  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  42
4-7 Feed adjustment screw and feed direction knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  43
5-1 Grease fitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  47
5-2 Box wrench over screw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48
5-3 Punches used for guard installation  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  48
5-4 Initial roller bearing locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49
5-5 Adjusting and tightening of the bushings and cap screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
5-6 Checking for play between the track ring and the stationary ring  . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  49
5-7 Location of M4 screw (left); cable end under M4 screw and jam nut with adjusting bolt (right)  . . . . . .  49
5-8 Barrel end of cable removal (left); Cable and housing cutters (right)  . . . . . . . . . . . . . . . . . . . . . . . . . .  50
5-9 Barrel end of cable with spring, ferrule installed on cable housing (left); cable installed in actuator housing 

Summary of Contents for H&S TOOL SPEED FACER ODF100





































































































































Reviews:

No comments

Related manuals for H&S TOOL SPEED FACER ODF100

Keithley 8009 Instruction Manual preview
8009
Brand: Keithley Pages: 36
Rain-Flo Irrigation 1200 Operating Manual preview
1200
Brand: Rain-Flo Irrigation Pages: 16
York Fitness G500 Owner'S Manual preview
G500
Brand: York Fitness Pages: 34
Rain-Flo Irrigation 2470 Operating Manual preview
2470
Brand: Rain-Flo Irrigation Pages: 20
3M Attest Auto-reader 390 Connectivity Technical Specifications preview
Attest Auto-reader 390
Brand: 3M Pages: 2
3M Attest 390 Quick Reference Manual preview
Attest 390
Brand: 3M Pages: 2
3M Ranger 245 Competency Checklist preview
Ranger 245
Brand: 3M Pages: 2
3M Dynapro ET 355 Monitor HL Installation Manual Addendum preview
Dynapro ET 355 Monitor HL
Brand: 3M Pages: 23
3M PELTOR WS LiteCom Plus Technical Data Sheet preview
PELTOR WS LiteCom Plus
Brand: 3M Pages: 7
3M Steri-Vac GS Series Site Planning & Installation Manual preview
Steri-Vac GS Series
Brand: 3M Pages: 52
Facsimile Genius Use And Maintenance Manual preview
Genius
Brand: Facsimile Pages: 16
Kawai CS11 Setting Manual preview
CS11
Brand: Kawai Pages: 10
Daktronics Sportsound SSR-300 Operation Manual preview
Sportsound SSR-300
Brand: Daktronics Pages: 42
unios Echo Quick Installation Manual preview
Echo
Brand: unios Pages: 2
Keller HPX Operating Instructions Manual preview
HPX
Brand: Keller Pages: 12
MacDon D50 Installation Manual preview
D50
Brand: MacDon Pages: 49
MacDon D50 Unloading And Assembly Instructions preview
D50
Brand: MacDon Pages: 49
MacDon D50 Quick Start Manual preview
D50
Brand: MacDon Pages: 4

Brands by name

Popular brands

Load more brands