Climax H&S TOOL SPEED FACER ODF100, Operating Manual

Page: 50 / 132

Page 32 ODF Speed Facer Operating Manual
one swivel hoist ring with the customer-sup-
plied anchor points and slings rated for the
machine weight and sling angle. See Figure 3-3.
3.3.3 Overhead mounting
The hazard with overhead mounting is the machine fall-
ing off the flange.
Mitigations include one of the following arrangements:
• Install the setup fingers on the back (top) of the
flange, on the “bottom” of the leveling feet
(see Figure 3-4).
• If the flange is too thick to allow for the use of
the setup fingers, secure the machine to anchor
points above the machine using a minimum of
two opposite swivel hoist rings with the cus-
tomer-supplied anchor points and slings rated
for the machine weight and sling angle. See Fig-
ure 3-3.
CAUTION
In all cases, these safety measures should be
considered during the risk assessment and the
machine restraints installed snug so that any
swinging or other machine movement is kept to an
absolute minimum.
3.4 M
ACHINE ASSEMBLY
Do the following to set up the ODF Speed Facer:
1. Complete the risk assessment checklist in
Table 1-2 on page 4.
2. Measure the OD of the flange to be machined.
3. Position the machine on a solid support for
installing the mounting feet (four feet for the
ODF30 and ODF40 models; eight feet for all
other models) according to the following tables.
WARNING
Failure to properly mount and tether the machine
may allow the machine to rotate or fall.
T
ABLE
3-1. ODF30 S
PEED
F
ACER MOUNTING FEET
Minimum OD in
inches (mm) Maximum OD in
inches (mm) Foot bolt
location Frame hole
location
27.02" (686 mm) 30.5" (775 mm) D 1
F
IGURE
3-5. B
OLT AND HOLE LOCATIONS
25.02" (636 mm) 28.5" (724 mm) C 1
23.02" (585 mm) 26.5" (673 mm) C 2
21.02" (534 mm) 24.5" (622 mm) B 2
19.02" (483 mm) 22.5" (572 mm) A 2
T
ABLE
3-2. ODF40 S
PEED
F
ACER MOUNTING FEET
Minimum OD in
inches (mm) Maximum OD in
inches (mm) Foot bolt
location Frame hole
location
37.02" (940 mm) 40.5" (1,029 mm) D 1
35.02" (890 mm) 38.5" (978 mm) C 1
33.02" (839 mm) 36.5" (927 mm) C 2
31.02" (788 mm) 34.5" (876 mm) B 2
29.02" (737 mm) 32.5" (826 mm) A 2
T
ABLE
3-3. ODF50 S
PEED
F
ACER MOUNTING FEET
Minimum OD in
inches (mm) Maximum OD in
inches (mm) Foot bolt
location Frame hole
location
47.02" (1,194 mm) 50.5" (1,283 mm) D 1
45.02" (1,144 mm) 48.5" (1,232 mm) C 1
43.02" (1,093 mm) 46.5" (1,181 mm) C 2
41.02" (1,042 mm) 44.5" (1,130 mm) B 2
39.02" (991 mm) 42.5" (1,080 mm) A 2
T
ABLE
3-1. ODF30 S
PEED
F
ACER MOUNTING FEET
(C
ONTIN
-
Minimum OD in
inches (mm) Maximum OD in
inches (mm) Foot bolt
location Frame hole
location