manualshive.com logo in svg

Climax H&S TOOL SPEED FACER ODF100, Operating Manual

Share
Download
Climax H&S TOOL SPEED FACER ODF100 Operating Manual Download Page 47

P/N 102615, Rev. 0

Page 29

 

3

SETUP

IN THIS CHAPTER:

3.1 R

ECEIPT

 

AND

 

INSPECTION

    -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -29

3.2 L

IFTING

 

AND

 

RIGGING

 -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -29

3.3 I

NSTALLATION

 

HAZARDS

    -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -30

3.3.1 H

ORIZONTAL

 

MOUNTING

   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -31

3.3.2 V

ERTICAL

 

MOUNTING

 -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -31

3.3.3 O

VERHEAD

 

MOUNTING

  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -32

3.4 M

ACHINE

 

ASSEMBLY

   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -32

3.4.1 C

HUCK

 

FEET

 

EXTENSIONS

    -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -34

3.4.2 C

HUCK

 

FOOT

 

SPACERS

 -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -34

3.4.3 C

ENTERING

 

AND

 

LEVELING

   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -34

3.4.4 I

NSTALLING

 

THE

 

CUTTING

 

BIT

 

OR

 

INSERT

 

HOLDER

 -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -35

3.4.5 I

NSTALLING

 

THE

 

OFFSET

 

TOOL

 

HOLDER

   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -36

3.4.6 R

OTATING

 

THE

 

TOOL

 

HEAD

  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -36

3.4.7 A

DJUSTING

 

THE

 

FEED

    -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -37

3.4.8 I

NSTALLING

 

THE

 

DRIVE

  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -37

3.4.9 C

ONNECTING

 

THE

 A

IR

 C

ADDY

    -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -38

3.4.10 I

NSTALLING

 

THE

 

HYDRAULIC

 

MOTOR

   -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -38

3.4.11 C

ONNECTING

 

THE

 HPU (

HYDRAULIC

 

POWER

 

UNIT

)    -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -  -38

This section describes the setup and assembly proce-
dures for the ODF Speed Facer.

3.1

R

ECEIPT

 

AND

 

INSPECTION

Your H&S product was inspected and tested prior to 
shipment, and packaged for normal shipment condi-
tions. H&S does not guarantee the condition of your 
machine upon delivery. 
When you receive your H&S product, perform the fol-
lowing receipt checks:

1. Inspect the shipping containers for damage.
2. Check the contents of the shipping containers 

against the included invoice to make sure that 
all components have been shipped.

3. Inspect all components for damage.

Contact H&S immediately to report damaged or missing 
components.

NOTICE

Keep the shipping container and all packing 
materials for future storage and shipping of the 
machine.

The machine ships from H&S with a heavy coating of LPS 
3. The recommended cleaner is LPS PreSolve Orange 
Degreaser. All parts must be cleaned before use.

3.2

L

IFTING

 

AND

 

RIGGING

Before unpacking the shipping containers, complete the 
risk assessment checklist in Table 1-2 on page 4.

Before lifting, make sure all parts are securely attached 
to the machine. 

Summary of Contents for H&S TOOL SPEED FACER ODF100





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands