manualshive.com logo in svg

Climax H&S TOOL SPEED FACER ODF100, Operating Manual

Share
Download
Climax H&S TOOL SPEED FACER ODF100 Operating Manual Download Page 14

Page vi

ODF Speed Facer Operating Manual

 LIST OF FIGURES (CONTINUED)

F

IGURE

P

AGE

(right) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  50
5-10 90° elbow, adjusting nut and jam nut (left); cable end shown at trimming location (right). . . . . . . . . .  50
5-11 Solder-treated cable end (left); cable end secured under the M4 screw (right). . . . . . . . . . . . . . . . . .  51
6-1 Alignment arrow (ODF80 shown)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54
6-2 Outside screw locations (ODF80 shown)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  54
6-3 Hoist ring, strap attachment point, and inner ring supports (ODF80 shown). . . . . . . . . . . . . . . . . . . . .  54
6-4 ODF30 Shipping container    . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55
6-5 ODF40 Shipping container  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  55
6-6  ODF50 Shipping container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56
6-7  ODF60 Shipping container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  56
6-8  ODF70 Shipping container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  57
6-9 Typical incline Speed Facer shipping frame (ODF80 shown) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  58
A-1 ODF30 Speed Facer assembly (P/N 88930)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  61
A-2 ODF30 Speed Facer assembly labels assembly (P/N 88930) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  62
A-3 ODF30 Speed Facer assembly parts list (P/N 88930)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
A-4 ODF40 Speed Facer assembly (P/N 86870)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  64
A-5 ODF40 Speed Facer labels assembly (P/N 86870)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
A-6 ODF40 Speed Facer parts list (P/N 86870)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  66
A-7 ODF50 Speed Facer assembly (P/N 86980)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  67
A-8 ODF50 Speed Facer labels assembly (P/N 86980)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
A-9 ODF50 Speed Facer parts list (P/N 86980)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  69
A-10 ODF60 Speed Facer assembly (P/N 86990)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  70
A-11 ODF60 Speed Facer label locations (P/N 86990). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  71
A-12 ODF60 Speed Facer parts list (P/N 86990)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  72
A-13 ODF70 Speed Facer assembly (P/N 87000)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  73
A-14 ODF70 Speed Facer label locations (P/N 87000). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  74
A-15 ODF70 Speed Facer parts list (P/N 87000)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  75
A-16 ODF80 Speed Facer assembly 1 (P/N 94770) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
A-17 ODF80 Speed Facer label locations (P/N 94770). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  77
A-18 ODF80 Speed Facer assembly parts list (P/N 94770)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  78
A-19 ODF90 Speed Facer assembly 1 (P/N 94780) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
A-20 ODF90 Speed Facer label locations (P/N 94780). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  80
A-21 ODF90 Speed Facer assembly parts list (P/N 94780)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  81
A-22 ODF100 Speed Facer assembly 1 (P/N 94790) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
A-23 ODF100 Speed Facer label locations (P/N 94790). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
A-24 ODF100 Speed Facer assembly parts list (P/N 94790)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  84
A-25 ODF110 Speed Facer assembly 1 (P/N 7639-S2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  85
A-26 ODF110 Speed Facer label locations (P/N 7639-S2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  86
A-27 ODF110 Speed Facer assembly parts list (P/N 7639-S2)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  87
A-28 ODF120 Speed Facer assembly (P/N 7639-S1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
A-29 ODF120 Speed Facer label locations (P/N 89210). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
A-30 ODF120 Speed Facer assembly parts list (P/N 89210)  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  90
A-31 Slide tool holder assembly (P/N 89210) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  91
A-32 Slide tool holder parts list (P/N 89210) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  92
A-33 Pneumatic conditioning unit assembly (P/N 101920) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

Summary of Contents for H&S TOOL SPEED FACER ODF100





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands