Climax H&S TOOL SPEED FACER ODF100 Operating Manual Download Page 76

Page: 76 / 132

Page 58

ODF Speed Facer Operating Manual

The ODF80 and larger models ship on their shipping
frame and accessories are stored in the toolbox.

IGURE

6-9. T

YPICAL

INCLINE

PEED

ACER

SHIPPING

FRAME

(ODF80

SHOWN

)

Squircle 1 in Figure 6-9 shows the lifting points for plac-
ing and removing the Speed Facer. These are also the
tie-down points for the ratchet straps.

Squircle 2 shows the support locations for uniform cra-
dling of the machine during storage and transport.

6.3

ECOMMISSIONING

To decommission the ODF Speed Facer prior to disposal,
remove the drive assembly and dispose of it separately

from the rest of the machine components. Refer to
Appendix A for component assembly information.

Summary of Contents for H&S TOOL SPEED FACER ODF100





































































































































Search results

Summary of Contents for H&S TOOL SPEED FACER ODF100

Reviews:

Related manuals for H&S TOOL SPEED FACER ODF100

Brands by name

Popular brands

Climax H&S TOOL SPEED FACER ODF100, Operating Manual

Search results

Summary of Contents for H&S TOOL SPEED FACER ODF100

Reviews:

Related manuals for H&S TOOL SPEED FACER ODF100

Brands by name

Popular brands