manualshive.com logo in svg

Climax H&S TOOL SPEED FACER ODF100, Operating Manual

Share
Download
Climax H&S TOOL SPEED FACER ODF100 Operating Manual Download Page 48

Page 30

ODF Speed Facer Operating Manual

DANGER

The ODF Speed Facer can weigh between 1,000 and 
5,000 lbs (490 and 1,840 kg) when fully assembled 
(see the tables in Section 2.4 on page 24). To 
prevent serious injury to yourself and others, 
always follow the operating procedures outlined in 
this manual, your own company rules, and local 
regulations for heavy lifting. Serious injury or 
fatalities can result from improper lifting methods.

Do the following for correct lifting:

1. Attach four 3/4" (19 mm) swivel hoist rings to 

the machine, if not already attached. 

CAUTION

Falling or uncontrolled swinging of machinery can 
cause serious injury or be fatal to the operator and 
bystanders. Only lift the machine by the 3/4" hoist 
rings identified in Figure 3-1. Do not lift the ODF 
Speed Facer using smaller lifting points located on 
the bridge or counterweight.
2. Attach customer-supplied rigging to the hoist 

rings on the machine.

CAUTION

Make sure the rigging is correctly attached before 
lifting the machine.

 

Lift the machine slowly, making 

sure that no components will be crushed or bent if 
the machine is lifted in the vertical orientation. If 
the rigging causes the machine to swing or become 
unstable, lower it and adjust the rigging.

3. Rig the machine out of the shipping crate.

3.3

I

NSTALLATION

 

HAZARDS

The installation stage can be dangerous, as it relies on 
the operator and other personnel following the recom-
mended safety precautions. Consider the following 
warnings carefully before undertaking the assembly pro-
cess.

WARNING

If not properly secured, this machine can fall and 
cause fatal injuries to personnel. Pay special 
attention to vertical flange and overhead mounting 
installations.

Secure all components to the machine before 
lifting. Use supplemental rigging during setup.

F

IGURE

 3-1. L

IFTING

 

POINTS

 (ODF40 

MACHINE

 

SHOWN

)

F

IGURE

 3-2. V

ERTICAL

 

HAZARD

Summary of Contents for H&S TOOL SPEED FACER ODF100





































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands