Climax H&S TOOL SPEED FACER ODF100 Operating Manual Download

Page: 60 / 132

Page 42

ODF Speed Facer Operating Manual

a) Loosen the two screws on the face of the

feedbox.

b) Pull out on the feedbox to free it from the

drive shaft of the radial slide.

c) Install the feedbox on the end of the axial

slide shaft and secure by tightening the
two screws.

10. For ODF70 and larger machines only: Reposition

a clip and Velcro strap to an empty hole on the
extension plate and secure the trip cable.

On ODF60 and smaller machines: Reposition a
clip and Velcro strap to an empty hole on the
face of the machine and secure the trip cable.

IGURE

4-5. R

EPOSITIONED

BACKFACING

COMPONENTS

4.3

PERATION

4.3.1

Starting the machine

Do the following to start the machine:

1. On the hydraulic motor drive machine, refer-

ence the included HPU (hydraulic power unit)
operating instructions for powering up the unit.
If the HPU is not being supplied as part of the

IGURE

4-6. A

CADDY

CONTROLS

Summary of Contents for H&S TOOL SPEED FACER ODF100





































































































































Search results

Summary of Contents for H&S TOOL SPEED FACER ODF100

Reviews:

Related manuals for H&S TOOL SPEED FACER ODF100

Brands by name

Popular brands

Climax H&S TOOL SPEED FACER ODF100, Operating Manual

Search results

Summary of Contents for H&S TOOL SPEED FACER ODF100

Reviews:

Related manuals for H&S TOOL SPEED FACER ODF100

Brands by name

Popular brands