manualshive.com logo in svg

Cisco ONS 15454 Series, Procedure Manual

The Cisco ONS 15454 Series Reference Manual is a comprehensive user guide for understanding and operating this remarkable product. Easily accessible for download on our website, this manual provides essential information to maximize the potential of your Cisco ONS 15454 Series, available for free at manualshive.com.

Share
Download
background image

6-58

Cisco ONS 15454 Procedure Guide, R5.0

August 2005

Chapter 6      Create Circuits and VT Tunnels

NTP-A191 Create an E-Series EtherSwitch Circuit (Multicard or Single-Card Mode)

Step 16

Click 

Next

.

Step 17

In the Circuit VLAN Selection area, click

 New VLAN

. If the desired VLAN already exists, continue 

with 

Step 20

.

Tip

You can also add VLANs in network view by choosing 

Tools > Manage VLANs

. In the All 

VLANs dialog box, click the 

Create

 button to open the Define New VLAN dialog box.

Step 18

In the Define New VLAN dialog box, complete the following:

•

VLAN Name—Assign an easily identifiable name to your VLAN.

•

VLAN ID—Assign a VLAN ID. The VLAN ID should be the next available number between 2 and 
4093 that is not already assigned to an existing VLAN. Each ONS 15454 network supports a 
maximum of 509 user-provisionable VLANs.

•

Topology Host—Choose the topology host ID from the drop-down list. 

Step 19

Click

 OK

.

Step 20

In the Circuit VLAN Selection area, highlight the VLAN name and click the arrow button (

>>

) to move 

the available VLANs to the Circuit VLANs column. 

Step 21

If you are building a single-card EtherSwitch circuit and want to disable spanning tree protection on this 
circuit, uncheck the 

Enable Spanning Tree

 check box and click 

OK 

in the Disabling Spanning Tree 

dialog box. The Enable Spanning Tree box remains checked or unchecked for the creation of the next 
single-card, point-to-point Ethernet circuit.

Caution

Disabling spanning-tree protection increases the likelihood of logic loops on an Ethernet network.

Caution

Turning off spanning tree on a circuit-by-circuit basis means that the ONS 15454 is no longer protecting 
the Ethernet circuit and that the circuit must be protected by another mechanism in the Ethernet network.

Caution

Multiple circuits with spanning tree protection enabled incur blocking if the circuits traverse the same 
E-Series card and use the same VLAN. 

Note

Spanning-tree rules prevent users from creating new circuits or modifying existing circuits if the circuits 
do not meet certain VLAN assignment constraints. If the VLAN set of the new circuit overlaps existing 
circuits, the same spanning-tree instance is used for all circuits. If the VLAN set of the new circuit 
overlaps with VLAN sets of existing circuits with different spanning-tree instances, the VLAN 
assignment fails. Cisco recommends that you plan VLAN assignments so that circuits with larger VLAN 
sets and a higher chance of overlap are added first. This means that if a circuit with an overlapping 
VLAN set is added, it collapses into the same spanning tree. To view circuits mapped to a spanning tree 
and their VLAN assignments, see the 

“DLP-A430 View Spanning Tree Information” task on page 21-9

.

Note

You can disable or enable spanning tree protection on a circuit-by-circuit basis only for single-card, 
point-to-point Ethernet circuits. Other E-Series Ethernet configurations disable or enable spanning tree 
on a port-by-port basis.

Summary of Contents for ONS 15454 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ONS 15454 Series

Daktronics RC-100 Operation Manual preview
RC-100
Brand: Daktronics Pages: 52
RKC INSTRUMENT FAREX SR MINI SYSTEM Communication Instruction Manual preview
FAREX SR MINI SYSTEM
Brand: RKC INSTRUMENT Pages: 82
PictureTel Videoconferencing system User Manual preview
Videoconferencing system
Brand: PictureTel Pages: 122
Parker 2003-CB-00 Technical Manual preview
2003-CB-00
Brand: Parker Pages: 47
Prology MCE-525UR Service Manual preview
MCE-525UR
Brand: Prology Pages: 37
TCP SmartStuff SmartBox Quick Start Manual preview
SmartStuff SmartBox
Brand: TCP Pages: 2
vistaCNC Mach III P1A Manual preview
Mach III P1A
Brand: vistaCNC Pages: 6
SEW-Eurodrive IPOS plus Manual preview
IPOS plus
Brand: SEW-Eurodrive Pages: 384
Jacuzzi JAUTPS Installation & Operation Manual preview
JAUTPS
Brand: Jacuzzi Pages: 28
babala Hydro-Pro Instruction Manual preview
Hydro-Pro
Brand: babala Pages: 30
BMW 65 41 2 163 268 Installation Instructions Manual preview
65 41 2 163 268
Brand: BMW Pages: 16
MPMan XRM 33 Manual preview
XRM 33
Brand: MPMan Pages: 5
AAD PL-100 Owner'S Information preview
PL-100
Brand: AAD Pages: 8
Roger Technology B72/DGS Instruction And Warnings For The Installer preview
B72/DGS
Brand: Roger Technology Pages: 8
NEC 0891069 Manual preview
0891069
Brand: NEC Pages: 58
Bosch B420 Setup & Troubleshooting preview
B420
Brand: Bosch Pages: 23
Sharp CD-BA2100 Operation Manual preview
CD-BA2100
Brand: Sharp Pages: 18
Sony CMT-SE5 Operating Instructions Manual preview
CMT-SE5
Brand: Sony Pages: 72

Brands by name

Popular brands

Load more brands